- 您現在的位置：買賣IC網 > PDF目錄383837 > ST16C580 (Exar Corporation) UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER PDF資料下載
參數資料
| 型號： | ST16C580 |
| 廠商： | Exar Corporation |
| 英文描述： | UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| 中文描述： | UART的16字節FIFO的和紅外線（IrDA）編碼/解碼器 |
| 文件頁數： | 14/41頁 |
| 文件大?。?/td> | 244K |
| 代理商： | ST16C580 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
ST16C580
14
Rev. 1.20
DMA Operation
The 580 FIFO trigger level provides additional flexibil-
ity to the user for block mode operation. LSR bits 5-6
provide an indication when the transmitter is empty or
has an empty location(s). The user can optionally
operate the transmit and receive FIFO’s in the DMA
mode (FCR bit-3). When the transmit and receive
FIFO’s are enabled and the DMA mode is deactivated
(DMA Mode “0”), the 580 activates the interrupt output
pin for each data transmit or receive operation. When
DMA mode is activated (DMA Mode “1”), the user
takes the advantage of block mode operation by
loading or unloading the FIFO in a block sequence
determined by the preset trigger level. In this mode,
the 580 sets the interrupt output pin when characters
in the transmit FIFO’s are below the transmit trigger
level, or the characters in the receive FIFO’s are
above the receive trigger level.
Sleep Mode
The 580 is designed to operate with low power con-
sumption. A special sleep mode is included to further
reduce power consumption when the chip is not being
used. With EFR bit-4 and IER bit-4 enabled (set to a
logic 1), the 580 enters the sleep mode but resumes
normal operation when a start bit is detected, a change
of state on any of the modem input pins RX, -RI, -CTS,
-DSR, -CD, or transmit data is provided by the user. If
the sleep mode is enabled and the 580 is awakened by
one of the conditions described above, it will return to
the sleep mode automatically after the last character
is transmitted or read by the user. In any case, the
sleep mode will not be entered while an interrupt(s) is
pending. The 580 will stay in the sleep mode of
operation until it is disabled by setting IER bit-4 to a
logic 0.
Loop-back Mode
The internal loop-back capability allows onboard diag-
nostics. In the loop-back mode the normal modem
interface pins are disconnected and reconfigured for
loop-back internally. In this mode MSR bits 4-7 are
also disconnected. However, MCR register bits 0-3
can be used for controlling loop-back diagnostic test-
ing. In the loop-back mode OP1 and OP2 in the MCR
register (bits 0-1) control the modem -RI and -CD
inputs respectively. MCR signals -DTR and -RTS (bits
0-1) are used to control the modem -CTS and -DSR
inputs respectively. The transmitter output (TX) and
the receiver input (RX) are disconnected from their
associated interface pins, and instead are connected
together internally (See Figure 12). The -CTS, -DSR,
-CD, and -RI are disconnected from their normal
modem control inputs pins, and instead are connected
internally to -DTR, -RTS, -OP1 and -OP2. Loop-back
test data is entered into the transmit holding register
via the user data bus interface, D0-D7. The transmit
UART serializes the data and passes the serial data to
the receive UART via the internal loop-back connec-
tion. The receive UART converts the serial data back
into parallel data that is then made available at the
user data interface, D0-D7. The user optionally com-
pares the received data to the initial transmitted data
for verifying error free operation of the UART TX/RX
circuits.
In this mode , the receiver and transmitter interrupts
are fully operational. The Modem Control Interrupts
are also operational. However, the interrupts can only
be read using lower four bits of the Modem Control
Register (MCR bits 0-3) instead of the four Modem
Status Register bits 4-7. The interrupts are still con-
trolled by the IER.
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C580CQ48 | UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| ST16C580IJ44 | UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| ST16C580IP40 | UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| ST16C580IQ48 | UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| ST16C580CP40 | Linear Voltage Regulator IC; Output Current Max:350mA; Supply Voltage Max:6V; Package/Case:8-TSSOP; Output Current:350mA; Output Voltage:3.3V; Current Rating:30.05A; Leaded Process Compatible:No; Output Voltage Max:3.3V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C580_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| ST16C580CJ44 | 制造商:EXAR 制造商全稱:EXAR 功能描述:UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| ST16C580CP40 | 制造商:EXAR 制造商全稱:EXAR 功能描述:UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER |
| ST16C580CQ-0A-EVB | 功能描述:界面開發工具 Supports C580 48 ld TQFP, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| ST16C580CQ48 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。