參數資料
型號： ST16C580
廠商： Exar Corporation
英文描述： UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER
中文描述： UART的16字節FIFO的和紅外線（IrDA）編碼/解碼器
文件頁數： 12/41頁
文件大小： 244K
代理商： ST16C580
ST16C580
12
Rev. 1.20
C1
22pF
C2
33pF
X1
1.8432 MHz
R1
50-120
R2
1M
X
X
Crystal oscillator connection
level. In this case the 580 FIFO may hold more charac-
ters than the programmed trigger level. Following the
removal of a data byte, the user should recheck LSR bit-
0 for additional characters. A Receive Time Out will not
occur if the receive FIFO is empty. The time out counter
is reset at the center of each stop bit received or each
time the receive holding register (RHR) is read (see
Figure 10, Receive Time-out Interrupt). The actual time
out value is T (
T
ime out length in bits) = 4 X P
(
P
rogrammed word length) + 12. To convert the time out
value to a character value, the user has to consider the
complete word length, including data information
length, start bit, parity bit, and the size of stop bit, i.e.,
1X, 1.5X, or 2X bit times.
Example -A: If the user programs a word length of 7,
with no parity and one stop bit, the time out will be:
T = 4 X 7( programmed word length) +12 = 40 bit times.
The character time will be equal to 40 / 9 = 4.4
characters, or as shown in the fully worked out ex-
ample: T = [(programmed word length = 7) + (stop bit
= 1) + (start bit = 1) = 9]. 40 (bit times divided by 9) =
4.4 characters.
Example -B: If the user programs the word length = 7,
with parity and one stop bit, the time out will be:
T = 4 X 7(programmed word length) + 12 = 40 bit times.
Character time = 40 / 10 [ (programmed word length
= 7) + (parity = 1) + (stop bit = 1) + (start bit = 1) = 4
characters.
Programmable Baud Rate Generator
The 580 supports high speed modem technologies
that have increased input data rates by employing
data compression schemes. For example a 33.6Kbps
modem that employs data compression may require a
115.2Kbps input data rate. A 128.0Kbps ISDN modem
that supports data compression may need an input
data rate of 460.8Kbps. The 580 can support a stan-
dard data rate of 921.6Kbps.
Single baud rate generator is provided for the trans-
mitter and receiver, allowing independent TX/RX
channel control. The programmable Baud Rate Gen-
erator is capable of accepting an input clock up to 24
MHz, as required for supporting a 1.5Mbps data rate.
The 580 can be configured for internal or external clock
operation. For internal clock oscillator operation, an
industry standard microprocessor crystal (parallel reso-
nant/ 22-33 pF load) is connected externally between
the XTAL1 and XTAL2 pins, with an external 1 M
resistor across it. Alternatively, an external clock can
be connected to the XTAL1 pin to clock the internal baud
rate generator for standard or custom rates.
The generator divides the input 16X clock by any
divisor from 1 to 2
16
-1. The 580 divides the basic
crystal or external clock by 16. Further division of this
16X clock provides two table rates to support low and
high data rate applications using the same system
design. The two rate tables are selectable through the
internal register, MCR bit-7. Setting MCR bit-7 to a
logic 1 provides an additional divide by 4 whereas,
setting MCR bit-7 to a logic 0 only divides by 1. (See
Table 4 and Figure 11). The frequency of the -
BAUDOUT output pin is exactly 16X (16 times) of the
selected baud rate (-BAUDOUT =16 x Baud Rate).
Customized Baud Rates can be achieved by selecting
the proper divisor values for the MSB and LSB sec-
tions of baud rate generator.
Programming the Baud Rate Generator Registers
相關PDF資料
PDF描述
ST16C580CQ48 UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER
ST16C580IJ44 UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER
ST16C580IP40 UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER
ST16C580IQ48 UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER
ST16C580CP40 Linear Voltage Regulator IC; Output Current Max:350mA; Supply Voltage Max:6V; Package/Case:8-TSSOP; Output Current:350mA; Output Voltage:3.3V; Current Rating:30.05A; Leaded Process Compatible:No; Output Voltage Max:3.3V
相關代理商/技術參數
參數描述
ST16C580_05 制造商:EXAR 制造商全稱:EXAR 功能描述:UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER
ST16C580CJ44 制造商:EXAR 制造商全稱:EXAR 功能描述:UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER
ST16C580CP40 制造商:EXAR 制造商全稱:EXAR 功能描述:UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER
ST16C580CQ-0A-EVB 功能描述:界面開發工具 Supports C580 48 ld TQFP, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
ST16C580CQ48 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*