- 您現在的位置：買賣IC網 > PDF目錄383837 > ST16C550 (Exar Corporation) UART with 16-Byte FIFO(通用異步接收器/發送器（帶16字節的先進先出）) PDF資料下載
參數資料
| 型號： | ST16C550 |
| 廠商： | Exar Corporation |
| 英文描述： | UART with 16-Byte FIFO(通用異步接收器/發送器（帶16字節的先進先出）) |
| 中文描述： | 的UART具有16字節FIFO（通用異步接收器/發送器（帶16字節的先進先出）） |
| 文件頁數： | 15/36頁 |
| 文件大小： | 235K |
| 代理商： | ST16C550 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
ST16C550
15
Rev. 4.20
IER BIT-3:
Logic 0 = Disable the modem status register interrupt.
(normal default condition)
Logic 1 = Enable the modem status register interrupt.
IER BIT 4-7:Not used and set to “0”.
FIFO Control Register (FCR)
This register is used to enable the FIFO’s, clear the
FIFO’s, set the transmit/receive FIFO trigger levels,
and select the DMA mode. The DMA, and FIFO
modes are defined as follows:
DMA MODE:
See description and DMA tables on page 11.
FCR BIT-0:
Logic 0 = Disable the transmit and receive FIFO.
(normal default condition)
Logic 1 = Enable the transmit and receive FIFO. This
bit must be a “1” when other FCR bits are written to or
they will not be programmed.
FCR BIT-1:
Logic 0 = No FIFO receive reset. (normal default
condition)
Logic 1 = Clears the contents of the receive FIFO and
resets the FIFO counter logic (the receive shift regis-
ter is not cleared or altered). This bit will return to a
logic 0 after clearing the FIFO.
FCR BIT-2:
Logic 0 = No FIFO transmit reset. (normal default
condition)
Logic 1 = Clears the contents of the transmit FIFO and
resets the FIFO counter logic (the transmit shift regis-
ter is not cleared or altered). This bit will return to a
logic 0 after clearing the FIFO.
FCR BIT-3:
Logic 0 = Set DMA mode “0”. (normal default condi-
tion)
Logic 1 = Set DMA mode “1.”
Transmit operation in mode “0”:
When the ST16C550 is in the ST16C450 mode
(FIFO’s disabled, FCR bit-0 = logic 0) or in the FIFO
mode (FIFO’s enabled, FCR bit-0 = logic 1, FCR bit-
3 = logic 0) and when there are no characters in the
transmit FIFO or transmit holding register, the -
TXRDY pin will be a logic 0. Once active the -TXRDY
pin will go to a logic 1 after the first character is loaded
into the transmit holding register.
Receive operation in mode “0”:
When the ST16C550 is in mode “0” (FCR bit-0 = logic
0) or in the FIFO mode (FCR bit-0 = logic 1, FCR bit-
3 = logic 0) and there is at least one character in the
receive FIFO, the -RXRDY pin will be a logic 0. Once
active the -RXRDY pin will go to a logic 1 when there
are no more characters in the receiver.
Transmit operation in mode “1”:
When the ST16C550 is in FIFO mode ( FCR bit-0 =
logic 1, FCR bit-3 = logic 1 ), the -TXRDY pin will be
a logic 1 when the transmit FIFO is completely full. It
will be a logic 0 if one or more FIFO locations are
empty.
Receive operation in mode “1”:
When the ST16C550 is in FIFO mode (FCR bit-0 =
logic 1, FCR bit-3 = logic 1) and the trigger level has
been reached, or a Receive Time Out has occurred,
the -RXRDY pin will go to a logic 0. Once activated, it
will go to a logic 1 after there are no more characters
in the FIFO.
FCR BIT 4-5: Not used.
FCR BIT 6-7: These bits are used to set the trigger level
for the receive FIFO interrupt.
An interrupt is generated when the number of characters
in the FIFO equals the programmed trigger level. How-
ever the FIFO will continue to be loaded until it is full.
BIT-7
BIT-6
RX FIFO trigger level
0
0
1
1
0
1
0
1
1
4
8
14
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C552 | Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）) |
| ST16C552A | Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）) |
| ST16C554DCJ68 | QUAD UART WITH 16-BYTE FIFOS |
| ST68C554 | QUAD UART WITH 16-BYTE FIFOS |
| ST16C554DIJ68 | Plug-In Relay; Contacts:DPDT; Contact Carry Current:15A; Coil Voltage AC Max:120V; Relay Mounting:Plug-In; Relay Terminals:Quick Connect; Coil Resistance:4430ohm RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C550_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:UART WITH 16-BYTE FIFO’s |
| ST16C550CJ44 | 制造商:Exar 功能描述:Bulk |
| ST16C550CJ44-F | 功能描述:UART 接口集成電路 2.97V-5.5V 16B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C550CJ44TR-F | 功能描述:UART 接口集成電路 SNGL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C550CP40 | 功能描述:UART 接口集成電路 SINGLE UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。