- 您現在的位置：買賣IC網 > PDF目錄383837 > ST16C2451 (Exar Corporation) 2.97V TO 5.5V DUART PDF資料下載
參數資料
| 型號： | ST16C2451 |
| 廠商： | Exar Corporation |
| 英文描述： | 2.97V TO 5.5V DUART |
| 中文描述： | 2.97V至5.5V杜阿爾特 |
| 文件頁數： | 8/29頁 |
| 文件大?。?/td> | 315K |
| 代理商： | ST16C2451 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
ST16C2450
2.97V TO 5.5V DUART
á
REV. 4.0.0
8
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100 ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins (see
Figure 4
), with an external 500 k
to
1 M
resistor across it. Alternatively, an external clock can be connected to the XTAL1 pin to clock the internal
baud rate generator for standard or custom rates. Typical oscillator connections are shown in
Figure 4
. For
further reading on oscillator circuit please see application note DAN108 on EXAR’s web site.
2.7
Programmable Baud Rate Generator
A single baud rate generator is provided for the transmitter and receiver, allowing independent TX/RX channel
control. The programmable Baud Rate Generator is capable of operating with a crystal frequency or external
clock of up to 24 MHz.
The 2450 divides the basic external clock by 16. The basic 16X clock provides table rates to support standard
and custom applications using the same system design. The Baud Rate Generator divides the input 16X clock
by any divisor from 1 to 2
16
-1. The rate table is configured via the DLL and DLM internal register functions.
Customized Baud Rates can be achieved by selecting the proper divisor values for the MSB and LSB sections
of baud rate generator.
Table 3
shows the standard data rates available with a 14.7456 MHz crystal or external clock at 16X sampling
rate. When using a non-standard frequency crystal or external clock, the divisor value can be calculated for
DLL/DLM with the following equation.
F
IGURE
4. T
YPICAL
OSCILLATOR
CONNECTIONS
divisor (decimal) = (XTAL1 clock frequency) / (serial data rate x 16)
C1
22-47 pF
C2
22-47 pF
Y1
1.8432 MHz
to
24 MHz
R1
0-120
(Optional)
R2
500 Κ 1 Μ
XTAL1
XTAL2
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C2552CJ44 | DUAL ASYNCHRONOUS RECEIVER/TRANSMITTER WITH FIFOs |
| ST16C2552IJ44 | DUAL ASYNCHRONOUS RECEIVER/TRANSMITTER WITH FIFOs |
| ST162552 | DUAL ASYNCHRONOUS RECEIVER/TRANSMITTER WITH FIFOs |
| ST16C2552CJ | 2.97V TO 5.5V DUAL UART WITH 16-BYTE FIFO |
| ST16C2552IJ | 2.97V TO 5.5V DUAL UART WITH 16-BYTE FIFO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C2550 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V DUART WITH 16-BYTE FIFO |
| ST16C2550_04 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V DUART WITH 16-BYTE FIFO |
| ST16C2550CJ-0A-EB | 功能描述:界面開發工具 Supports C2550 44 ld PLCC, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| ST16C2550CJ44 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V DUART WITH 16-BYTE FIFO |
| ST16C2550CJ44-F | 功能描述:UART 接口集成電路 2.97V-5.5V 16B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。