- 您現在的位置：買賣IC網 > PDF目錄383837 > ST162552 (Exar Corporation) DUAL ASYNCHRONOUS RECEIVER/TRANSMITTER WITH FIFOs PDF資料下載
參數資料
| 型號： | ST162552 |
| 廠商： | Exar Corporation |
| 英文描述： | DUAL ASYNCHRONOUS RECEIVER/TRANSMITTER WITH FIFOs |
| 中文描述： | 雙異步接收器/發送器與FIFO的 |
| 文件頁數： | 4/28頁 |
| 文件大?。?/td> | 121K |
| 代理商： | ST162552 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
3-138
ST16C2552
S
Symbol
Pin
Signal Type
Pin Description
SYMBOL DESCRIPTION
INT A/B
34,17
O
Interrupt output A/B. (active high) This pin goes high (when
enabled by the interrupt enable register) whenever a re-
ceiver error, receiver data available, transmitter empty, or
modem status condition flag is detected.
MF* A/B
35,19
O
OP2* (interrupt enable), BAUDOUT* and RXRDY* outputs.
These outputs are multiplexed via Alternate Function Reg-
ister. When output enable function is selected the MF* pin
stays high when INT out pin is set to three state mode and
goes low when INT pin is enabled. See bit-3 modem control
register (MCR bit-3). When BAUDOUT function is selected,
the 16 X TX/RX Baud rate clock output is generated.
RXRDY function can be selected to use to request a DMA
transfer of data from the Receive data FIFO. OP2* is the
default signal and it is selected immediately after master
reset or power-up.
TXRDY* A/B
1,32
O
Transmit ready. (active low) This pin goes high when the
transmit FIFO of the ST16C2552 is full. It can be used as a
single or multi-transfer.
RTS* A/B
36,23
O
Request to send A/B (active low). To indicate that the
transmitter has data ready to send. Writing a “1” in the
modem control register (MCR bit-1 ) will set this pin to a low
state. After the reset this pin will be set to high. Note that
this pin does not have any effect on the transmit or receive
operation.
DTR* A/B
37,27
O
Data terminal ready A/B (active low). To indicate that
ST16C2552 is ready to receive data. This pin can be
controlled via the modem control register (MCR bit-0).
Writing a “1” at the MCR bit-0 will set the DTR* output to low.
This pin will be set to high state after writing a “0” to that
register or after the reset . Note that this pin does not have
any effect on the transmit or receive operation.
RESET
21
I
Master reset. (active high) A high on this pin will reset all the
outputs and internal registers. The transmitter output and
the receiver input will be disabled during reset time.
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C2552CJ | 2.97V TO 5.5V DUAL UART WITH 16-BYTE FIFO |
| ST16C2552IJ | 2.97V TO 5.5V DUAL UART WITH 16-BYTE FIFO |
| ST16C452IJ68 | DUAL UART WITH PARALLEL PRINTER PORT |
| ST16C452IJ68PS | DUAL UART WITH PARALLEL PRINTER PORT |
| ST16C452CJ68 | Power Supply IC; Number of Outputs:1; Supply Voltage Max:5.5V; Package/Case:10-MSOP; Leaded Process Compatible:No; Output Current:150mA; Output Voltage Max:1.3V; Peak Reflow Compatible (260 C):No; Power Dissipation:481mW |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST1638 | 制造商:STANSON 制造商全稱:STANSON 功能描述:Step-Up DC/DC Converter High Efficiency PFM |
| ST1638-XXS23 | 制造商:STANSON 制造商全稱:STANSON 功能描述:Step-Up DC/DC Converter High Efficiency PFM |
| ST1638-XXS89 | 制造商:STANSON 制造商全稱:STANSON 功能描述:Step-Up DC/DC Converter High Efficiency PFM |
| ST163D00 | 功能描述:撥動開關 TOGGLE RoHS:否 制造商:C&K Components 觸點形式:DPDT 開關功能:ON - ON - ON 電流額定值: 電壓額定值 AC:20 V 電壓額定值 DC:20 V 功率額定值:0.4 VA 端接類型:V-Bracket 安裝風格: 端子密封:Epoxy 觸點電鍍:Gold 照明:Not Illuminated |
| ST163X377 | 制造商:Allied Controls Incorporated 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。