參數資料
型號： SST49LF008C-33-4C-NHE
元件分類： PROM
英文描述： 1M X 8 FLASH 3V PROM, 11 ns, PQCC32
封裝： ROHS COMPLIANT, PLASTIC, MS-016AE, LCC-32
文件頁數： 2/36頁
文件大?。?/td> 509K
代理商： SST49LF008C-33-4C-NHE
10
Advance Information
4 Mbit / 8 Mbit LPC Serial Flash
SST49LF004C / SST49LF008C
200 Silicon Storage Technology, Inc.
S71292-00-000
1/06
PIN DESCRIPTIONS
TABLE
1: PIN DESCRIPTION
Symbol
Pin Name
Type1
1. I=Input, O=Output
Interface
Functions
AAI LPC
LCLK
Clock
I
X
To accept a clock input from the control unit
LAD[3:0]
Address
and Data
I/O
X
To provide LPC bus information,
such as addresses and command Inputs/Outputs data.
LFRAME# Frame
I
X
To indicate the start of a data transfer operation;
also used to abort an LPC cycle in progress.
RST#
Reset
I
X
To reset the operation of the device
INIT#
Initialize
I
X
This is the second reset pin for in-system use.
This pin is internally combined with the RST# pin.
If this pin or RST# pin is driven low, identical operation is exhibited.
ID[3:0]
Identification
Inputs
I
X
These four pins are part of the mechanism that allows multiple parts to be
attached to the same bus. The strapping of these pins is used to identify
the component. The boot device must have ID[3:0]=0000, all subsequent
devices should use sequential up-count strapping. These pins are inter-
nally pulled-down with a resistor between 20-100 K
Ω. When in AAI mode,
these pins operate identically as in Firmware Memory cycles.
GPI[4:0]
General
Purpose
Inputs
I
X
These individual inputs can be used for additional board flexibility.
The state of these pins can be read through LPC registers. These inputs
should be at their desired state before the start of the LPC clock cycle dur-
ing which the read is attempted, and should remain in place until the end
of the Read cycle. Unused GPI pins must not be floated.
GPI[2:4] are ignored when in AAI mode.
TBL#
Top Block Lock
I
X
When low, prevents programming to the boot block sectors at top of device
memory. When TBL# is high it disables hardware write protection for the
top block sectors. This pin cannot be left unconnected.
TBL# setting is ignored when in AAI mode.
WP#/AAI
Write Protect
I
X
When low, prevents programming to all but the highest addressable block
(Boot Block). When WP# is high it disables hardware write protection for
these blocks. This pin cannot be left unconnected.
WP#/AAI
AAI Enable
I
X
When set to the Supervoltage VH = 9V, configures the device to program
multiple bytes in AAI mode. When brought to VIL/VIH, returns device to
LPC mode.
RY/BY#
Ready/Busy#
O
X
Open drain output that indicates the device is ready to accept data in an
AAI mode, or that the internal cycle is complete.
Used in conjunction with LD# pin to switch between these two flag states.
LD#
Load-Enable#
I
X
Input pin which when low, indicates the host is loading data in an AAI pro-
gramming cycle. If LD# is high, the host signals the AAI interface that it is
terminating a command. LD# low/high switches the RY/BY# output from a
“buffer free” flag to a “programming complete” flag.
VDD
Power Supply
PWR
X
To provide power supply (3.0-3.6V)
VSS
Ground
PWR
X
Circuit ground (0V reference)
NC
No Connection
N/A
Unconnected pins.
T1.0 1292
相關PDF資料
PDF描述
SSU-131MAT SLIDE SWITCH, SP3T, LATCHED, 0.3A, 4VDC, SURFACE MOUNT-RIGHT ANGLE
SSU-121ART SLIDE SWITCH, SPDT, LATCHED, 0.3A, 4VDC, SURFACE MOUNT-RIGHT ANGLE
SSW-102-22-F-D-VS 4 CONTACT(S), FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT, SOCKET
SSW-102-22-F-S-VS 2 CONTACT(S), FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT, SOCKET
SSW-102-22-G-D-VS 4 CONTACT(S), FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT, SOCKET
相關代理商/技術參數
參數描述
SST49LF008C-33-4C-WHE 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:4 Mbit / 8 Mbit LPC Serial Flash
SST49LF016C 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:16 Mbit LPC Serial Flash
SST49LF016C-33-4C-EIE 功能描述:閃存 16M (2Mx8) 33MHz 3.0-3.6V Commercial RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
SST49LF016C-33-4C-EIE-T 功能描述:閃存 3.0 to 3.6V 16Mbit LPC Firmware 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
SST49LF016C-33-4C-NHE 功能描述:閃存 16M (2Mx8) 33MHz 3.0-3.6V Commercial RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*