- 您現在的位置：買賣IC網 > PDF目錄385811 > S75PL127JCEBFWU0 (Spansion Inc.) Power supply woltage of 2.7 to 3.1 volt PDF資料下載
參數資料
| 型號： | S75PL127JCEBFWU0 |
| 廠商： | Spansion Inc. |
| 英文描述： | Power supply woltage of 2.7 to 3.1 volt |
| 中文描述： | 功率2月7號至三月一日伏的電源woltage |
| 文件頁數： | 31/183頁 |
| 文件大?。?/td> | 1409K |
| 代理商： | S75PL127JCEBFWU0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁
32
S29PL127J/S29PL064J/S29PL032J for MCP
S29PL127J_064J_032J_MCP_00_A3 August 12, 2004
P r e l i m i n a r y
By issuing the DYB Write command sequences, the DYBs will be set or cleared,
thus placing each sector in the protected or unprotected state. These are the so-
called Dynamic Locked or Unlocked states. They are called dynamic states be-
cause it is very easy to switch back and forth between the protected and
unprotected conditions. This allows software to easily protect sectors against in-
advertent changes yet does not prevent the easy removal of protection when
changes are needed. The DYBs maybe set or cleared as often as needed.
The PPBs allow for a more static, and difficult to change, level of protection. The
PPBs retain their state across power cycles because they are non-volatile. Indi-
vidual PPBs are set with a command but must all be cleared as a group through
a complex sequence of program and erasing commands. The PPBs are also lim-
ited to 100 erase cycles.
The PPB Lock bit adds an additional level of protection. Once all PPBs are pro-
grammed to the desired settings, the PPB Lock may be set to “1”. Setting the PPB
Lock disables all program and erase commands to the non-volatile PPBs. In ef-
fect, the PPB Lock Bit locks the PPBs into their current state. The only way to clear
the PPB Lock is to go through a power cycle. System boot code can determine if
any changes to the PPB are needed; for example, to allow new system code to
be downloaded. If no changes are needed then the boot code can set the PPB
Lock to disable any further changes to the PPBs during system operation.
The WP#/ACC write protect pin adds a final level of hardware protection to sec-
tors SA1-133, SA1-134, SA2-0 and SA2-1. When this pin is low it is not possible
to change the contents of these sectors. These sectors generally hold system
boot code. The WP#/ACC pin can prevent any changes to the boot code that could
override the choices made while setting up sector protection during system
initialization.
For customers who are concerned about malicious viruses there is another level
of security - the persistently locked state. To persistently protect a given sector
or sector group, the PPBs associated with that sector need to be set to “1”. Once
all PPBs are programmed to the desired settings, the PPB Lock should be set to
“1”. Setting the PPB Lock automatically disables all program and erase commands
to the Non-Volatile PPBs. In effect, the PPB Lock “freezes” the PPBs into their cur-
rent state. The only way to clear the PPB Lock is to go through a power cycle.
It is possible to have sectors that have been persistently locked, and sectors that
are left in the dynamic state. The sectors in the dynamic state are all unprotected.
If there is a need to protect some of them, a simple DYB Write command se-
quence is all that is necessary. The DYB write command for the dynamic sectors
switch the DYBs to signify protected and unprotected, respectively. If there is a
need to change the status of the persistently locked sectors, a few more steps
are required. First, the PPB Lock bit must be disabled by either putting the device
through a power-cycle, or hardware reset. The PPBs can then be changed to re-
flect the desired settings. Setting the PPB lock bit once again will lock the PPBs,
and the device operates normally again.
The best protection is achieved by executing the PPB lock bit set command early
in the boot code, and protect the boot code by holding WP#/ACC = VIL.
Table 8
contains all possible combinations of the DYB, PPB, and PPB lock relating
to the status of the sector.
In summary, if the PPB is set, and the PPB lock is set, the sector is protected and
the protection can not be removed until the next power cycle clears the PPB lock.
相關PDF資料 |
PDF描述 |
|---|---|
| S75PL127JCFBFWB2 | Power supply woltage of 2.7 to 3.1 volt |
| S7AH-06E | NON-ISOLATED DC/DC CONVERTERS 4.5 13.2V Input / 1.0 ? 3.3V Output / 6A |
| S7AH-08B250 | NON-ISOLATED DC/DC CONVERTERS 5V Input / 0.9V - 3.3V Output / 8A |
| S7AH-08B330 | NON-ISOLATED DC/DC CONVERTERS 5V Input / 0.9V - 3.3V Output / 8A |
| S7AH-08B | NON-ISOLATED DC/DC CONVERTERS 5V Input / 0.9V - 3.3V Output / 8A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S75PL127JCEBFWU2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCEBFWU3 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCF | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCFBAWB0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCFBAWB2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
發布緊急采購，3分鐘左右您將得到回復。