- 您現在的位置：買賣IC網 > PDF目錄385811 > S75PL127JCEBFWU0 (Spansion Inc.) Power supply woltage of 2.7 to 3.1 volt PDF資料下載
參數資料
| 型號： | S75PL127JCEBFWU0 |
| 廠商： | Spansion Inc. |
| 英文描述： | Power supply woltage of 2.7 to 3.1 volt |
| 中文描述： | 功率2月7號至三月一日伏的電源woltage |
| 文件頁數： | 128/183頁 |
| 文件大?。?/td> | 1409K |
| 代理商： | S75PL127JCEBFWU0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁當前第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁
December 15, 2004 S29GLxxxN_MCP_A1
S29GLxxxN MirrorBit
TM
Flash Family
129
A d v a n c e I n f o r m a t i o n
local Spansion representative. Word programming is supported for backward
compatibility with existing Flash driver software and for occasional writing of in-
dividual words. Use of Write Buffer Programming is strongly recommended for
general programming use when more than a few words are to be programmed.
The effective word programming time using Write Buffer Programming is much
shorter than the single word programming time.
Any word cannot be pro-
grammed from “0” back to a “1.”
Attempting to do so may cause the device
to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate the operation
was successful. However, a succeeding read will show that the data is still “0.”
Only erase operations can convert a “0” to a “1.”
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to program words to the device
faster than using the standard program command sequence. The unlock bypass
command sequence is initiated by first writing two unlock cycles. This is followed
by a third write cycle containing the unlock bypass command, 20h. The device
then enters the unlock bypass mode. A two-cycle unlock bypass program com-
mand sequence is all that is required to program in this mode. The first cycle in
this sequence contains the unlock bypass program command, A0h; the second
cycle contains the program address and data. Additional data is programmed in
the same manner. This mode dispenses with the initial two unlock cycles required
in the standard program command sequence, resulting in faster total program-
ming time.
Table 12
shows the requirements for the command sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock By-
pass Reset commands are valid. To exit the unlock bypass mode, the system
must issue the two-cycle unlock bypass reset command sequence. (See
Table
12
).
Write Buffer Programming
Write Buffer Programming allows the system write to a maximum of 16 words/32
bytes in one programming operation. This results in faster effective programming
time than the standard programming algorithms. The Write Buffer Programming
command sequence is initiated by first writing two unlock cycles. This is followed
by a third write cycle containing the Write Buffer Load command written at the
Sector Address in which programming will occur. The fourth cycle writes the sec-
tor address and the number of word locations, minus one, to be programmed. For
example, if the system will program 6 unique address locations, then 05h should
be written to the device. This tells the device how many write buffer addresses
will be loaded with data and therefore when to expect the Program Buffer to Flash
command. The number of locations to program cannot exceed the size of the
write buffer or the operation will abort.
The fifth cycle writes the first address location and data to be programmed. The
write-buffer-page is selected by address bits A
MAX
–A
4
. All subsequent address/
data pairs must fall within the selected-write-buffer-page. The system then
writes the remaining address/data pairs into the write buffer. Write buffer loca-
tions may be loaded in any order.
The write-buffer-page address must be the same for all address/data pairs loaded
into the write buffer. (This means Write Buffer Programming cannot be performed
across multiple write-buffer pages. This also means that Write Buffer Program-
ming cannot be performed across multiple sectors. If the system attempts to load
programming data outside of the selected write-buffer page, the operation will
abort.)
相關PDF資料 |
PDF描述 |
|---|---|
| S75PL127JCFBFWB2 | Power supply woltage of 2.7 to 3.1 volt |
| S7AH-06E | NON-ISOLATED DC/DC CONVERTERS 4.5 13.2V Input / 1.0 ? 3.3V Output / 6A |
| S7AH-08B250 | NON-ISOLATED DC/DC CONVERTERS 5V Input / 0.9V - 3.3V Output / 8A |
| S7AH-08B330 | NON-ISOLATED DC/DC CONVERTERS 5V Input / 0.9V - 3.3V Output / 8A |
| S7AH-08B | NON-ISOLATED DC/DC CONVERTERS 5V Input / 0.9V - 3.3V Output / 8A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S75PL127JCEBFWU2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCEBFWU3 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCF | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCFBAWB0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCFBAWB2 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
發(fā)布緊急采購，3分鐘左右您將得到回復。