- 您現在的位置：買賣IC網 > PDF目錄385792 > S25FL001D0FNFI001 (SPANSION LLC) 2 Megabit, 1 Megabit CMOS 3.0 Volt Flash Memory with 25 MHz SPI Bus Interface PDF資料下載
參數資料
| 型號： | S25FL001D0FNFI001 |
| 廠商： | SPANSION LLC |
| 元件分類： | DRAM |
| 英文描述： | 2 Megabit, 1 Megabit CMOS 3.0 Volt Flash Memory with 25 MHz SPI Bus Interface |
| 中文描述： | 1M X 1 SPI BUS SERIAL EEPROM, PDSO8 |
| 封裝： | 6 X 5 MM, LEAD FREE, WSON-8 |
| 文件頁數： | 22/38頁 |
| 文件大?。?/td> | 488K |
| 代理商： | S25FL001D0FNFI001 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
22
S25FL Family (Serial Peripheral Interface)
30167A+1 June 9, 2004
P r e l i m i n a r y I n f o r m a t i o n
Figure 13. Bulk Erase (BE) Instruction Sequence
Software Protect (SP)
The Software Protect (SP) instruction implemented in this device is compatible
with industry-standard Software Protect (SP) operation. For this device, this in-
struction has no real function since the Standby Current (I
SB
) on this device is
the same as the Deep Power-down Current in our competitor's devices.
It is recommended that the standard Standby mode be used for the lowest power
current draw, as well as the Software Protect (SP) as an extra software protection
mechanism when this device is not in active use. In this mode, the device ignores
all Write, Program and Erase instructions. Chip Select (CS#) must be driven Low
for the entire duration of the sequence.
The Software Protect (SP) instruction is entered by driving Chip Select (CS#)
Low, followed by the instruction code on Serial Data Input (SI). Chip Select (CS#)
must be driven Low for the entire duration of the sequence.
The instruction sequence is shown in
Figure 14
.
Driving Chip Select (CS#) High after the eighth bit of the instruction code has
been latched in deselects the device, and puts the device in the Standby mode (if
there is no internal cycle currently in progress). As soon as Chip Select (CS#) is
driven high, it requires a delay of t
SP
currently in progress before Software Pro-
tect mode is entered.
Once the device has entered the Software Protect mode, all instructions are ig-
nored except the Release from Software Protect (RES) or Read ID (READ_ID)
instruction. The Release from Software Protect and Read Electronic Signature
(RES) instruction also allows the Electronic Signature of the device to be output
on Serial Data Output (SO).
The Software Protect mode automatically stops at Power-down, and the device
always Powers-up in the Standby mode.
0
1
2
4
5
6
7
Instruction
CS#
SCK
SI
3
相關PDF資料 |
PDF描述 |
|---|---|
| S25XXXH | SCR |
| S2516MH | SCR |
| S29GL032A30FFI012 | 64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology |
| S29GL032A100FAI013 | 64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology |
| S29GL032A100FAIR10 | 64 Megabit, 32 Megabit, and 16 Megabit 3.0-Volt only Page Mode Flash Memory Featuring 200 nm MirrorBit Process Technology |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S25FL001D0FNFI003 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:2 Megabit, 1 Megabit CMOS 3.0 Volt Flash Memory with 25 MHz SPI Bus Interface |
| S25FL001D0FNFI011 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:2 Megabit, 1 Megabit CMOS 3.0 Volt Flash Memory with 25 MHz SPI Bus Interface |
| S25FL001D0FNFI013 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:2 Megabit, 1 Megabit CMOS 3.0 Volt Flash Memory with 25 MHz SPI Bus Interface |
| S25FL002D | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:2 Megabit, 1 Megabit CMOS 3.0 Volt Flash Memory with 25 MHz SPI Bus Interface |
| S25FL002D0FMAI001 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:2 Megabit, 1 Megabit CMOS 3.0 Volt Flash Memory with 25 MHz SPI Bus Interface |
發布緊急采購，3分鐘左右您將得到回復。