- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C6P466D0A0A00 MICROCONTROLLER, UUC140 PDF資料下載
參數資料
| 型號： | S1C6P466D0A0A00 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MICROCONTROLLER, UUC140 |
| 封裝： | DIE-140 |
| 文件頁數： | 144/174頁 |
| 文件大小： | 1582K |
| 代理商： | S1C6P466D0A0A00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁當前第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁
S1C6P466 TECHNICAL MANUAL
EPSON
61
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Programmable Timer)
4.10.3 Counter mode
The programmable timer can operate in two counter modes, timer mode and event counter mode. It can
be selected by software.
(1) Timer mode
The timer mode counts down using the prescaler output as an input clock. In this mode, the program-
mable timer operates as a periodical timer using the OSC1 or OSC3 oscillation clock as a clock source.
Timer 0 can operate in both the timer mode and the event counter mode. The mode can be switched
using the timer 0 counter mode selection register EVCNT. When the EVCNT register is set to "0",
timer 0 operates in the timer mode.
Timer 1 operates only in the timer mode.
At initial reset, this mode is set.
Refer to Section 4.10.2, "Setting of initial value and counting down" for basic operation and control.
The input clock in the timer mode is generated by the prescaler built into the programmable timer.
The prescaler generates the input clock by dividing the OSC1 or OSC3 oscillation clock. Refer to the
next section for setting the input clock.
(2) Event counter mode
The timer 0 has an event counter function that counts an external clock input to the input port K13.
This function is selected by writing "1" to the timer 0 counter mode selection register EVCNT. The
timer 1 operates only in the timer mode, and cannot be used as an event counter.
In the event counter mode, the clock is supplied to timer 0 from outside of the IC, therefore, the
settings of the timer 0 prescaler division ratio selection registers PTPS00 and PTPS01 and the settings
of the timer 0 source clock selection register CKSEL0 become invalid.
Count down timing can be selected from either the falling or rising edge of the input clock using the
timer 0 pulse polarity selection register PLPOL. When "0" is written to the PLPOL register, the falling
edge is selected, and when "1" is written, the rising edge is selected. The count down timing is shown
in Figure 4.10.3.1.
K13 input
Count data
n
n-1
n-2
n-3
n-4
n-5
n-6
PLPOL
EVCNT
01
1
PTRUN0
Fig. 4.10.3.1 Timing chart in event counter mode
The event counter mode also includes a noise reject function to eliminate noise such as chattering on
the external clock (K13 input signal). This function is selected by writing "1" to the timer 0 function
selection register FCSEL.
When "with noise rejector" is selected, an input pulse width for both low and high levels must be 0.98
msec* or more to count reliably. The noise rejecter allows the counter to input the clock at the second
falling edge of the internal 2,048 Hz* signal after changing the input level of the K13 input port
terminal. Consequently, the pulse width of noise that can reliably be rejected is 0.48 msec* or less.
(
: fOSC1 = 32.768 kHz).
Figure 4.10.3.2 shows the count down timing with noise rejecter.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C6S2L7D | 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, UUC58 |
| S1C6S2A7F | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
| S1C6S2B7F | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
| S1C6S2N7D | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, UUC58 |
| S1C6S2N7F0A0100 | MICROCONTROLLER, PQFP60 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C-6-S | 制造商:GRIPCO 功能描述: |
| S1C7309X | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR |
| S1C7309X01 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR |
| S1C88349 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
| S1C88649 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。