參數資料
型號： S1C6P466D0A0A00
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, UUC140
封裝： DIE-140
文件頁數： 107/174頁
文件大?。?/td> 1582K
代理商： S1C6P466D0A0A00
28
EPSON
S1C6P466 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Input Ports)
SIK00–SIK03: K0 port interrupt selection register (FF20H)
SIK10–SIK13: K1 port interrupt selection register (FF24H)
Selects the ports to be used for the K00–K03 and K10–K13 input interrupts.
When "1" is written: Enable
When "0" is written: Disable
Reading: Valid
Enables the interrupt for the input ports (K00–K03, K10–K13) for which "1" has been written into the
interrupt selection registers (SIK00–SIK03, SIK10–SIK13). The input port set for "0" does not affect the
interrupt generation condition.
At initial reset, these registers are set to "0".
KCP00–KCP03: K0 port input comparison register (FF22H)
KCP10–KCP13: K1 port input comparison register (FF26H)
Interrupt conditions for terminals K00–K03 and K10–K13 can be set with these registers.
When "1" is written: Falling edge
When "0" is written: Rising edge
Reading: Valid
The interrupt conditions can be set for the rising or falling edge of input for each of the eight bits (K00–
K03 and K10–K13), through the input comparison registers (KCP00–KCP03 and KCP10–KCP13).
For KCP00–KCP03, a comparison is done only with the ports that are enabled by the interrupt among
K00–K03 by means of the SIK00–SIK03 registers. For KCP10–KCP13, a comparison is done only with the
ports that are enabled by the interrupt among K10–K13 by means of the SIK10–SIK13 registers.
At initial reset, these registers are set to "1".
EIK0: K0 input interrupt mask register (FFE4HD0)
EIK1: K1 input interrupt mask register (FFE5HD0)
Masking the interrupt of the input port can be selected with these registers.
When "1" is written: Enable
When "0" is written: Mask
Reading: Valid
With these registers, masking of the input port interrupt can be selected for each of the two systems (K00–
K03, K10–K13).
At initial reset, these registers are set to "0".
IK0: K0 input interrupt factor flag (FFF4HD0)
IK1: K1 input interrupt factor flag (FFF5HD0)
These flags indicate the occurrence of input interrupt.
When "1" is read: Interrupt has occurred
When "0" is read: Interrupt has not occurred
When "1" is written: Flag is reset
When "0" is written: Invalid
The interrupt factor flags IK0 and IK1 are associated with K00–K03 and K10–K13, respectively. From the
status of these flags, the software can decide whether an input interrupt has occurred.
The interrupt factor flag is set to "1" when the interrupt condition is established regardless of the interrupt
mask register setting. However, the interrupt does not occur to the CPU when the interrupt is masked.
These flags are reset to "0" by writing "1" to them.
After an interrupt occurs, the same interrupt will occur again if the interrupt enabled state (I flag = "1") is
set or the RETI instruction is executed unless the interrupt factor flag is reset. Therefore, be sure to reset
(write "1" to) the interrupt factor flag in the interrupt service routine before shifting to the interrupt
enabled state.
At initial reset, these flags are set to "0".
相關PDF資料
PDF描述
S1C6S2L7D 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, UUC58
S1C6S2A7F 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60
S1C6S2B7F 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60
S1C6S2N7D 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, UUC58
S1C6S2N7F0A0100 MICROCONTROLLER, PQFP60
相關代理商/技術參數
參數描述
S1C-6-S 制造商:GRIPCO 功能描述:
S1C7309X 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR
S1C7309X01 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR
S1C88349 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
S1C88649 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*