參數資料
型號: S1C63466D
元件分類: 微控制器/微處理器
英文描述: 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC140
封裝: DIE-140
文件頁數: 127/135頁
文件大小: 1053K
代理商: S1C63466D
S1C63466 TECHNICAL MANUAL
EPSON
83
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Serial Interface)
PUL10: SIN (P10) pull-up control register (FF45HD0)
PUL12: SCLK (P12) pull-up control register (FF45HD2)
Sets the pull-up of the SIN terminal and the SCLK terminals (in the slave mode).
When "1" is written: Pull-up ON
When "0" is written: Pull-up OFF
Reading: Valid
Sets the pull-up resistor built into the SIN (P10) and SCLK (P12) terminals to ON or OFF. (Pull-up resistor
is only built in the port selected by mask option.)
SCLK pull-up is effective only in the slave mode. In the master mode, the PUL12 register can be used as a
general purpose register.
At initial reset, these registers are set to "1" and pull-up goes ON.
SCS1, SCS0: Clock mode selection register (FF71HD0, D1)
Selects the synchronous clock (SCLK) for the serial interface.
Table 4.11.5.2 Synchronous clock selection
SCS1
1
0
SCS0
1
0
1
0
Mode
Master mode
Slave mode
Synchronous clock
OSC1
OSC1 /2
Programmable timer
External clock
The maximum clock is limited to 1 MHz.
Synchronous clock (SCLK) is selected from among the above 4 types: 3 types of internal clock and
external clock.
When the programmable timer is selected, the signal that is generated by dividing the underflow signal
of the programmable timer (timer 1) in 1/2 is used as the synchronous clock. In this case, the program-
mable timer must be controlled before operating the serial interface. Refer to Section 4.10, "Programmable
Timer" for the control of the programmable timer.
At initial reset, external clock is selected.
SCPS: Clock phase selection register (FF71HD2)
Selects the timing for reading in the serial data input from the SIN (P10) terminal.
When negative polarity is selected:
When "1" is written: Falling edge of SCLK
When "0" is written: Rising edge of SCLK
Reading: Valid
When positive polarity is selected:
When "1" is written: Rising edge of SCLK
When "0" is written: Falling edge of SCLK
Reading: Valid
Select whether the fetching for the serial input data to registers (SD0–SD7) at the rising edge or falling
edge of the synchronous signal.
Pay attention to the polarity of the synchronous clock selected by the mask option because the selection
content is different.
The input data fetch timing may be selected but output timing for output data is fixed at the falling edge
of SCLK (when negative polarity is selected) or at the rising edge of SCLK (when positive polarity is
selected).
At initial reset, this register is set to "0".
相關PDF資料
PDF描述
S1C63466F 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP144
S1C63567F0A0100 MICROCONTROLLER, PQFP144
S1C63653F 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100
S1C6F567D0A0100 MICROCONTROLLER, UUC141
S1C6N3B0D0A0100 MICROCONTROLLER, UUC54
相關代理商/技術參數
參數描述
S1C63557D04Q000 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT
S1C63567 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63616 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63632 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C63653 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller