- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C63466D 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC140 PDF資料下載
參數資料
| 型號： | S1C63466D |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, UUC140 |
| 封裝： | DIE-140 |
| 文件頁數： | 116/135頁 |
| 文件大小： | 1053K |
| 代理商： | S1C63466D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁當前第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁
S1C63466 TECHNICAL MANUAL
EPSON
73
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Programmable Timer)
FCSEL: Timer 0 function selection register (FFC0HD1)
Selects whether the noise rejector of the clock input circuit will be used or not in the event counter mode.
When "1" is written: With noise rejecter
When "0" is written: Without noise rejecter
Reading: Valid
When "1" is written to the FCSEL register, the noise rejecter is used and counting is done by an external
clock (K13) with 0.98 msec* or more pulse width. The noise rejecter allows the counter to input the clock
at the second falling edge of the internal 2,048 Hz* signal after changing the input level of the K13 input
port terminal. Consequently, the pulse width of noise that can reliably be rejected is 0.48 msec* or less.
(
: fOSC1 = 32.768 kHz).
When "0" is written to the FCSEL register, the noise rejector is not used and the counting is done directly
by an external clock input to the K13 input port terminal.
Setting of this register is effective only when timer 0 is used in the event counter mode.
At initial reset, this register is set to "0".
PLPOL: Timer 0 pulse polarity selection register (FFC0HD0)
Selects the count pulse polarity in the event counter mode.
When "1" is written: Rising edge
When "0" is written: Falling edge
Reading: Valid
The count timing in the event counter mode (timer 0) is selected from either the falling edge of the
external clock input to the K13 input port terminal or the rising edge. When "0" is written to the PLPOL
register, the falling edge is selected and when "1" is written, the rising edge is selected.
Setting of this register is effective only when timer 0 is used in the event counter mode.
At initial reset, this register is set to "0".
RLD00–RLD07: Timer 0 reload data register (FFC4H, FFC5H)
RLD10–RLD17: Timer 1 reload data register (FFC6H, FFC7H)
Sets the initial value for the counter.
The reload data written in this register is loaded to the respective counters. The counter counts down
using the data as the initial value for counting.
Reload data is loaded to the counter when the counter is reset by writing "1" to the PTRST0 or PTRST1
register, or when counter underflow occurs.
At initial reset, these registers are set to "00H".
PTD00–PTD07: Timer 0 counter data (FFC8H, FFC9H)
PTD10–PTD17: Timer 1 counter data (FFCAH, FFCBH)
Count data in the programmable timer can be read from these latches.
The low-order 4 bits of the count data in timer 0 can be read from PTD00–PTD03, and the high-order data
can be read from PTD04–PTD07. Similarly, for timer 1, the low-order 4 bits can be read from PTD10–
PTD13, and the high-order data can be read from PTD14–PTD17.
Since the high-order 4 bits are held by reading the low-order 4 bits, be sure to read the low-order 4 bits
first.
Since these latches are exclusively for reading, the writing operation is invalid.
At initial reset, these counter data are set to "00H".
相關PDF資料 |
PDF描述 |
|---|---|
| S1C63466F | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP144 |
| S1C63567F0A0100 | MICROCONTROLLER, PQFP144 |
| S1C63653F | 4-BIT, FLASH, 4 MHz, MICROCONTROLLER, CQFP100 |
| S1C6F567D0A0100 | MICROCONTROLLER, UUC141 |
| S1C6N3B0D0A0100 | MICROCONTROLLER, UUC54 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63557D04Q000 | 制造商:Seiko Instruments Inc (SII) 功能描述:EPSON MCU 4BIT |
| S1C63567 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63616 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63632 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63653 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。