- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C60A13F 4-BIT, MROM, 1.2 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | S1C60A13F |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 1.2 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | PLASTIC, QFP14-80 |
| 文件頁數： | 55/104頁 |
| 文件大?。?/td> | 850K |
| 代理商： | S1C60A13F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁當前第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
46
EPSON
S1C60N13 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (LCD Driver)
(3) Output specification
The segment terminals (SEG0–SEG37) are selected by mask option in pairs for either segment signal
output or DC output (VDD and VSS binary output). When DC output is selected, the data corre-
sponding to COM0 of each segment terminal is output.
When DC output is selected, either complementary output or Pch open drain output can be selected
for each terminal by mask option.
Note: The terminal pairs are the combination of SEG (2
n) and SEG (2n + 1) (where n is an integer from 0 to 18).
(4) Drive bias
For the drive bias of the S1C60N13 or the S1C60L13, either 1/3 bias or 1/2 bias can be selected by the
mask option. When using the LCD system voltage regulator, it is fixed at 1/3 bias.
4.8.4 Control of LCD driver
Table 4.8.4.1 shows the LCD driver's control bits and their addresses. Figure 4.8.4.1 shows the display
memory map.
Table 4.8.4.1 Control bits of LCD driver
Address
Comment
D3
D2
Register
D1
D0
Name
Init 1
10
2E8H
CSDC1
ETI2
ETI8
ETI32
R/W
CSDC1
ETI2
ETI8
ETI32
0
Static
Enable
Dynamic
Mask
LCD drive switch
Interrupt mask register (clock timer 2 Hz)
Interrupt mask register (clock timer 8 Hz)
Interrupt mask register (clock timer 32 Hz)
2D0H
000
CSDC2
R
R/W
0 3
CSDC2
– 2
1
–
Normal
–
All off
Unused
LCD all off control
1
2
Initial value at initial reset
Not set in the circuit
3
4
Always "0" being read
Reset (0) immediately after being read
5 Undefined
Address
Page
Low
High
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0 or 2
4
5
6
Display memory (38 words
× 4 bits)
Page 0: R/W, Page 2: W only
Unused area
Fig. 4.8.4.1 Display memory map
CSDC2: LCD all Off control (2D0HD0)
Controls the LCD display.
When "1" is written : LCD displayed
When "0" is written : LCD is all off
Read-out : Valid
By writing "0" to the CSDC2 register, all the LCD dots goes off, and when "1" is written, it returns to
normal display.
Writing "0" outputs an off waveform to the SEG terminals, and does not affect the content of the display
memory.
After an initial reset, CSDC2 is set to "1".
CSDC1: LCD drive switch (2E8HD3)
The LCD drive format can be selected with this switch.
When "1" is written : Static drive
When "0" is written : Dynamic drive
Read-out : Valid
At initial reset, dynamic drive (CSDC1 = "0") is selected.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C60L16F0A0100 | 4-BIT, MROM, 0.032768 MHz, MICROCONTROLLER, PQFP80 |
| S1C60N01F | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP48 |
| S1C60N02D | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, UUC52 |
| S1C60L02 | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
| S1C60N04D | 4-BIT, MROM, 2 MHz, MICROCONTROLLER, UUC48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C60A16 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60L05 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60L08 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60L16 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60N05 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。