- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C60A13F 4-BIT, MROM, 1.2 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | S1C60A13F |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 1.2 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | PLASTIC, QFP14-80 |
| 文件頁數： | 36/104頁 |
| 文件大?。?/td> | 850K |
| 代理商： | S1C60A13F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
S1C60N13 TECHNICAL MANUAL
EPSON
29
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (I/O Ports)
4.6 I/O Ports (P00–P03, P10–P13)
4.6.1 Configuration of I/O ports
The S1C60N13 Series has eight bits (4 bits
× 2) of general-purpose I/O ports. Figure 4.6.1.1 shows the
configuration of the I/O ports.
The four bits of each of the I/O ports P00–P03 and P10–P13 can be set to either input mode or output
mode. Modes can be set by writing data to the I/O control register.
I/O control
register
Address
Data
bus
Address
P
VSS
Register
Input
control
Fig. 4.6.1.1 Configuration of I/O port
The P10–P12 I/O port terminals are shared with the serial interface input/output terminals and the serial
interface is enabled by mask option.
4.6.2 Mask option
(1) Output specification
The output specification during output mode (IOC = "1") of these I/O ports can be set with the mask
option for either complementary output or Pch open drain output. This setting can be performed for
each bit of each port.
However, when Pch open drain output has been selected, voltage in excess of the power voltage must
not be applied to the port.
(2) Serial interface
The serial interface can be enabled by mask option. When the serial interface is enabled, the P10, P11
and P12 terminals are used as the serial I/O port.
4.6.3 I/O control register and I/O mode
Input or output mode can be set for the four bits of I/O port P00–P03 and I/O port P10–P13 by writing
data into the corresponding I/O control register IOC0 and IOC1.
To set the input mode, "0" is written to the I/O control register. When an I/O port is set to input mode, it
becomes high impedance status and works as an input port.
However, the input line is pulled down when input data is read.
The output mode is set when "1" is written to the I/O control register. When an I/O port set to output
mode works as an output port, it outputs a high signal (VDD) when the port output data is "1", and a low
signal (VSS) when the port output data is "0".
At initial reset, the I/O control registers are set to "0", and the I/O port enters the input mode.
When the serial interface is used, the IOC1 register controls only the P13 port.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C60L16F0A0100 | 4-BIT, MROM, 0.032768 MHz, MICROCONTROLLER, PQFP80 |
| S1C60N01F | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP48 |
| S1C60N02D | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, UUC52 |
| S1C60L02 | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
| S1C60N04D | 4-BIT, MROM, 2 MHz, MICROCONTROLLER, UUC48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C60A16 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60L05 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60L08 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60L16 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60N05 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。