參數資料
型號： RH80530GZ009512
元件分類： 微處理器
英文描述： Microprocessor
中文描述： 微處理器
文件頁數： 81/89頁
文件大?。?/td> 1672K
代理商： RH80530GZ009512
Mobile Intel
Pentium
III Processor-M Datasheet
298340-002
Datasheet
81
NC (No Connect)
All signals named NC (No Connect) must be left unconnected.
NCTRL (I - Analog)
The NCTRL signal provides the AGTL pull down impedance control. The processor samples this
input to determine the N-channel pull-down device strength when it is the driving agent. An external
14 ohm (1% tolerance) pull-up resistor to V
CCT
is required for this signal. Please refer to platform
design guide for implementation details.
NMI (I - 1.5V Tolerant)
The NMI (Non-Maskable Interrupt) indicates that an external interrupt has been generated. NMI
becomes the LINT1 signal when the APIC is disabled. Asserting NMI causes an interrupt with an
internally supplied vector value of 2. An external interrupt-acknowledge transaction is not generated. If
NMI is asserted during the execution of an NMI service routine, it remains pending and is recognized
after the IRET is executed by the NMI service routine. At most, one assertion of NMI is held pending.
NMI is rising edge sensitive.
PICCLK (I – 1.8V Tolerant)
The PICCLK (APIC Clock) signal is an input clock to the processor and system logic or I/O APIC that
is required for operation of the processor, system logic, and I/O APIC components on the APIC bus.
PICD[1:0] (I/O - 1.5V Tolerant Open-drain)
The PICD[1:0] (APIC Data) signals are used for bi-directional serial message passing on the APIC
bus. They must be connected to the appropriate pins/balls of all APIC bus agents, including the
processor and the system logic or I/O APIC components. If the PICD0 signal is sampled low on the
active-to-inactive transition of the RESET# signal, then the APIC is hardware disabled. For the
Mobile Intel Pentium
III
Processor-M, the APIC is required to be hardware enabled as described in
Section 7.1.3
PLL1, PLL2 (Analog)
The PLL1 and PLL2 signals provide isolated analog decoupling is required for the internal PLL. See
Section 3.2.2 for a description of the analog decoupling circuit.
PRDY# (O - AGTL)
The PRDY# (Probe Ready) signal is a processor output used by debug tools to determine processor
debug readiness.
PREQ# (I - 1.5V Tolerant)
The PREQ# (Probe Request) signal is used by debug tools to request debug operation of the processor.
PWRGOOD (I – 1.8V Tolerant)
PWRGOOD (Power Good) is a 1.8-V tolerant input. The processor requires this signal to be a clean
indication that clocks and the power supplies (V
CC
, V
CCT
, etc.) are stable and within their
specifications. Clean implies that the signal will remain low, (capable of sinking leakage current) and
相關PDF資料
PDF描述
RH80530NZ001256 Microprocessor
RH80530NZ004256 MICROPROCESSOR|32-BIT|CMOS|PGA|478PIN|CERAMIC
RH80530NZ006256 MICROPROCESSOR|32-BIT|CMOS|PGA|478PIN|CERAMIC
RH80530NZ009256 MICROPROCESSOR|32-BIT|CMOS|PGA|478PIN|CERAMIC
RH80530WZ014256 Microprocessor
相關代理商/技術參數
參數描述
RH80530GZ866512 制造商:Rochester Electronics LLC 功能描述:MOBILE P3 PROCESSOR; 866 MHZ; 512K OD; 1.4V; BGA2 - Bulk
RH80530MZ733256 制造商:Rochester Electronics LLC 功能描述:- Bulk
RH80530NZ001256 制造商:Rochester Electronics LLC 功能描述:- Bulk
RH80530NZ001256S L6AB 制造商:Intel 功能描述:MPU Celeron? Processor 64-Bit 0.13um 1GHz 478-Pin uFCPGA
RH80530NZ004256 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROPROCESSOR|32-BIT|CMOS|PGA|478PIN|CERAMIC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*