參數資料
型號： PIC18F46J50-I/PT
廠商： Microchip Technology
文件頁數： 108/164頁
文件大?。?/td> 0K
描述： IC PIC MCU FLASH 64KB 44-TQFP
產品培訓模塊： XLP Deep Sleep Mode
PIC18 J Series MCU Overview
PIC18F MPLAB® Starter Kit
8-bit PIC® Microcontroller Portfolio
標準包裝： 160
系列： PIC® XLP™ 18F
核心處理器： PIC
芯體尺寸： 8-位
速度： 48MHz
連通性： I²C，SPI，UART/USART，USB
外圍設備： 欠壓檢測/復位，DMA，POR，PWM，WDT
輸入/輸出數： 34
程序存儲器容量： 64KB（32K x 16）
程序存儲器類型： 閃存
RAM 容量： 3.8K x 8
電壓 - 電源 (Vcc/Vdd)： 2.15 V ~ 3.6 V
數據轉換器： A/D 13x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 44-TQFP
包裝： 托盤
產品目錄頁面： 657 (CN2011-ZH PDF)
配用： AC164330-ND - MODULE SKT FOR 44TQFP 18F45J10
PIC18F46J50 FAMILY
DS39931D-page 48
2011 Microchip Technology Inc.
TABLE 4-1:
LOW-POWER MODES
4.1.3
CLOCK TRANSITIONS AND STATUS
INDICATORS
The length of the transition between clock sources is
the sum of two cycles of the old clock source and three
to four cycles of the new clock source. This formula
assumes that the new clock source is stable.
Two bits indicate the current clock source and its
status:
OSTS
(OSCCON<3>)
and
T1RUN
(T1CON<6>). In general, only one of these bits will be
set in a given power-managed mode. When the OSTS
bit is set, the primary clock would be providing the
device clock. When the T1RUN bit is set, the Timer1
oscillator would be providing the clock. If neither of
these bits is set, INTRC would be clocking the device.
4.1.4
MULTIPLE SLEEP COMMANDS
The power-managed mode that is invoked with the
SLEEP
instruction is determined by the setting of the
IDLEN and DSEN bits at the time the instruction is exe-
cuted. If another SLEEP instruction is executed, the
device will enter the power-managed mode specified
by IDLEN and DSEN at that time. If IDLEN or DSEN
have changed, the device will enter the new
power-managed mode specified by the new setting.
4.2
Run Modes
In the Run modes, clocks to both the core and
peripherals are active. The difference between these
modes is the clock source.
4.2.1
PRI_RUN MODE
The PRI_RUN mode is the normal, full-power execu-
tion mode of the microcontroller. This is also the default
mode upon a device Reset unless Two-Speed Start-up
for details). In this mode, the OSTS bit is set (see
4.2.2
SEC_RUN MODE
The SEC_RUN mode is the compatible mode to the
“clock switching” feature offered in other PIC18
devices. In this mode, the CPU and peripherals are
clocked from the Timer1 oscillator. This gives users the
option of low-power consumption while still using a
high-accuracy clock source.
SEC_RUN mode is entered by setting the SCS<1:0>
bits to ‘01’. The device clock source is switched to the
Timer1 oscillator (see Figure 4-1), the primary
oscillator is shut down, the T1RUN bit (T1CON<6>) is
set and the OSTS bit is cleared.
Mode
DSCONH<7>
OSCCON<7,1:0>
Module Clocking
Available Clock and Oscillator Source
DSEN(1)
IDLEN(1)
SCS<1:0>
CPU
Peripherals
Sleep
00
N/A
Off
Timer1 oscillator and/or RTCC may optionally be
enabled
Deep Sleep
10
N/A
Off(2)
Off
RTCC can run uninterrupted using the Timer1 or
internal low-power RC oscillator
PRI_RUN
0
N/A
00
Clocked
The normal, full-power execution mode; primary
clock source (defined by FOSC<2:0>)
SEC_RUN
0
N/A
01
Clocked
Secondary – Timer1 oscillator
RC_RUN
0
N/A
11
Clocked
Postscaled internal clock
PRI_IDLE
01
00
Off
Clocked
Primary clock source (defined by FOSC<2:0>)
SEC_IDLE
01
Off
Clocked
Secondary – Timer1 oscillator
RC_IDLE
01
11
Off
Clocked
Postscaled internal clock
Note 1:
IDLEN and DSEN reflect their values when the SLEEP instruction is executed.
2:
Deep Sleep turns off the voltage regulator for ultra low-power consumption. See Section 4.6 “Deep Sleep
for more information.
Note:
Executing a SLEEP instruction does not
necessarily place the device into Sleep
mode. It acts as the trigger to place the
controller into either the Sleep or Deep
Sleep mode, or one of the Idle modes,
depending on the setting of the IDLEN bit.
Note:
The Timer1 oscillator should already be
running prior to entering SEC_RUN
mode. If the T1OSCEN bit is not set when
the SCS<1:0> bits are set to ‘01’, entry to
SEC_RUN mode will not occur. If the
Timer1 oscillator is enabled, but not yet
running, device clocks will be delayed until
the oscillator has started. In such situa-
tions, initial oscillator operation is far from
stable and unpredictable operation may
result.
相關PDF資料
PDF描述
PIC18F46K20-E/P IC PIC MCU FLASH 32KX16 40-DIP
PIC18F46K20-I/MV MCU PIC 64KB FLASH 40QFN
PIC18F47J53-I/ML IC PIC MCU 128KB FLASH 44QFN
PIC18F65K90-I/MR IC MCU 8BIT 32KB FLASH 64QFN
PIC18F66K80-I/MR MCU PIC 64KB FLASH 64QFN
相關代理商/技術參數
參數描述
PIC18F46J50T-I/ML 功能描述:8位微控制器 -MCU Full Spd USB 64KB 4KBRAM nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F46J50T-I/PT 功能描述:8位微控制器 -MCU Full Spd USB 64KB 4KBRAM nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F46J53-I/ML 功能描述:8位微控制器 -MCU 64KB Flash 4KB RAM 12MIPS nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F46J53-I/PT 功能描述:8位微控制器 -MCU 64KB Flash 4KB RAM 12MIPS nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F46J53T-I/ML 功能描述:8位微控制器 -MCU USB 64KB Flash 4KB RAM 12 MIPS 12b ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*