- 您現在的位置：買賣IC網 > PDF目錄1958 > P89LPC9107FN,112 (NXP Semiconductors)IC 80C51 MCU FLASH 1K 14-DIP PDF資料下載
參數資料
| 型號： | P89LPC9107FN,112 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 28/39頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 80C51 MCU FLASH 1K 14-DIP |
| 標準包裝： | 28 |
| 系列： | LPC900 |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 18MHz |
| 連通性： | UART/USART |
| 外圍設備： | 欠壓檢測/復位，LED，POR，PWM，WDT |
| 輸入/輸出數： | 12 |
| 程序存儲器容量： | 1KB（1K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 128 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.4 V ~ 3.6 V |
| 數據轉換器： | A/D 4x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 14-DIP（0.300"，7.62mm） |
| 包裝： | 管件 |
| 配用： | DB-TSSOP-LPC9107-ND - BOARD FOR LPC9107 TSSOP 622-1006-ND - SOCKET ADAPTER BOARD 622-1003-ND - KIT FOR LCD DEMO 568-1759-ND - EMULATOR DEBUGGER/PROGRMMR LPC9X |
| 其它名稱： | 935282288112 P89LPC9107FN P89LPC9107FN-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
P89LPC9102_9103_9107_3
NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 03 — 10 July 2007
34 of 61
NXP Semiconductors
P89LPC9102/9103/9107
8-bit microcontrollers with two-clock accelerated 80C51 core
8.14.2 Slow-down mode using the DIVM register
Slow-down mode is achieved by dividing down the OSCCLK frequency to generate CCLK.
This division is accomplished by conguring the DIVM register to divide OSCCLK by up to
510 times. This feature makes it possible to temporarily run the CPU at a lower rate,
reducing power consumption. By dividing the clock, the CPU can retain the ability to
respond to events that would not exit Idle mode by executing its normal program at a lower
rate. This can also allow bypassing the oscillator start-up time in cases where
Power-down mode would otherwise be used. The value of DIVM may be changed by the
program at any time without interrupting code execution.
8.14.3 Power-down mode
The Power-down mode stops the oscillator in order to minimize power consumption. The
P89LPC9102/9103/9107 exits Power-down mode via any reset, or certain interrupts. In
Power-down mode, the power supply voltage may be reduced to the data retention
voltage VDDR. This retains the RAM contents at the point where Power-down mode was
entered. SFR contents are not guaranteed after VDD has been lowered to VDDR, therefore
it is highly recommended to wake-up the processor via reset in this case. VDD must be
raised to within the operating range before the Power-down mode is exited.
Some chip functions continue to operate and draw power during Power-down mode,
increasing the total power used during Power-down mode. These include: Brownout
detect, watchdog timer, comparators (note that comparator can be powered-down
separately), and RTC/system timer. The internal RC oscillator is disabled unless both the
RC oscillator has been selected as the system clock and the RTC is enabled.
8.14.4 Total Power-down mode
This is the same as Power-down mode except that the brownout detection circuitry and
the voltage comparators are also disabled to conserve additional power. The internal RC
oscillator is disabled unless both the RC oscillator has been selected as the system clock
and the RTC is enabled. If the internal RC oscillator is used to clock the RTC during
Power-down mode, there will be high power consumption. Please use an external low
frequency clock to achieve low power with the RTC running during Power-down mode.
8.15 Reset
The P1.5/RST pin can function as either an active-LOW reset input or as a digital input,
P1.5. The RPE (Reset Pin Enable) bit in UCFG1, when set to logic 1, enables the external
reset input function on P1.5. When cleared, P1.5 may be used as an input pin.
Remark: During a power-up sequence, the RPE selection is overridden and this pin will
always function as a reset input. An external circuit connected to this pin should not
hold this pin LOW during a power-on sequence as this will keep the device in reset.
After power-up this input will function either as an external reset input or as a digital input
as dened by the RPE bit. Only a power-up reset will temporarily override the selection
dened by RPE bit. Other sources of reset will not override the RPE bit.
characteristics”) before power is reapplied, in order to ensure a power-on reset.
Reset can be triggered from the following sources:
External reset pin (during power-up or if user congured via UCFG1)
相關PDF資料 |
PDF描述 |
|---|---|
| P89LPC9161FDH,129 | IC 80C51 MCU FLASH 2KB 16TSSOP |
| P89LPC917FDH,129 | IC 80C51 MCU FLASH 2K 16-TSSOP |
| P89LPC9221FDH,512 | IC 80C51 MCU FLASH 8K 20-TSSOP |
| P89LPC9321FN,112 | IC 80C51 MCU FLASH 8K 28-DIP |
| P89LPC932A1FA,112 | IC 80C51 MCU FLASH 8K 28-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC912 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
| P89LPC912FDH | 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 1K FLASH TSSOP14 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 1K FLASH, TSSOP14 |
| P89LPC912FDH,129 | 功能描述:8位微控制器 -MCU 80C51 1K FL 128B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC912FDH129 | 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 18MHZ TSSOP-14 |
| P89LPC912HDH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with two-clock 80C51 core, 1 kB 3 V flash with 128-byte RAM |
發布緊急采購，3分鐘左右您將得到回復。