參數資料
型號： OMAP5910(DSP)
英文描述： Dual-Core Processor
中文描述： 雙核處理器
文件頁數： 34/160頁
文件大?。?/td> 1997K
代理商： OMAP5910(DSP)
Introduction
22
August 2002 Revised August 2003
SPRS197B
Table 24. Signal Description (Continued)
GDY
BALL
SIGNAL
TYPE
DESCRIPTION
GZG
BALL
EMIFS FLASH and Asynchronous Memory Interface (Continued)
FLASH.A[24:1]
L7,
K3,
K4,
L8,
J1,
J3,
J4,
J2,
K7,
H3,
H4,
K8,
G2,
G3,
G4,
F3,
J7,
E3,
F4,
D2,
E4,
C1,
D3,
J8
J3,
J4,
H6,
H5,
H2,
H4,
H3,
G2,
G1,
G5,
G3,
G4,
E1,
F2,
F4,
F3,
F5,
D2,
E4,
E3,
C2,
C1,
G6,
B1
EMIFS address bus. Address output bus for all EMIFS accesses. FLASH.A[24:1]
provides the upper 24 bits of a 25-bit byte address. The byte enables must be
used to implement 8-bit accesses.
O/Z
FLASH.RDY
H7
C3
EMIFS ready. Active-high ready input used to suspend the EMIFS interface when
the external memory or asynchronous device is not ready to continue the current
cycle.
It is recommended that this pin should be pulled high externally and
unused. See the
OMAP5910 Dual-Core Processor Silicon Errata
(literature
number SPRZ016) for more details.
I
LCD Interface
LCD.VS
D14
D11
LCD vertical sync output. LCD.VS is the frame clock which signals the start of a
new frame of pixels to the LCD panel. In TFT mode, LCD.VS is the vertical
synchronization signal.
O
LCD.HS
H12
E11
LCD horizontal sync. LCD.HS is the line clock which signals the end of a line of
pixels to the LCD panel. In TFT mode, LCD.HS is the horizontal synchronization
signal.
O
LCD.AC
B15
A11
LCD AC-bias. LCD.AC is used to signal the LCD to switch the polarity of the row
and column power supplies to counteract charge buildup causing DC offset. In
TFT mode, LCD.AC is used as the output enable to latch LCD pixel data using the
pixel clock.
O
LCD.PCLK
C15
A12
LCD pixel clock output. Clock output provided to synchronize pixel data to the
LCD panels. In passive mode, LCD.PCLK only transitions when LCD.P[15:0] is
valid. In active mode, LCD.PCLK transitions continuously and LCD.AC is used as
the output enable when LCD.P[15:0] is valid.
O
I = Input, O = Output, Z = High-Impedance
All core voltage supplies should be tied to the same voltage level (within 0.3 V). During system prototyping phases, it may be useful to maintain
a capability for independent measurement of core supply currents to facilitate power optimization experiments.
§See Sections 5.6.1 and 5.6.2 for special VSS considerations with oscillator circuits.
相關PDF資料
PDF描述
OMAP5910(RISC) Dual-Core Processor
OMC506 Closed Loop Speed Controller For 3-Phase Brushless DC Motor MP-3T Package
OMC507 5 Amp. Push-Pull 3-Phase Brushless DC Motor Controller Driver(5A,推挽三相無刷直流電機控制驅動器)
OMC510 36V Hi-Rel Three-Phase Brushless DC Motor Controller in a PCB-1 package
OMC510 DSP-Based Three-Phase Brushless DC Motor Controller(基于DSP的三相無刷直流電機控制器)
相關代理商/技術參數
參數描述
OMAP5910GGZG1 制造商:Rochester Electronics LLC 功能描述:- Bulk
OMAP5910GGZG2 制造商:Rochester Electronics LLC 功能描述:- Bulk
OMAP5910JGDY1R 功能描述:IC OMAP DUAL-CORE PROC 289-BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:OMAP-59xx 標準包裝:60 系列:SCC 處理器類型:Z380 特點:全靜電 Z380 CPU 速度:20MHz 電壓:5V 安裝類型:表面貼裝 封裝/外殼:144-LQFP 供應商設備封裝:144-LQFP 包裝:托盤
OMAP5910JGDY2 功能描述:數字信號處理器和控制器 - DSP, DSC Applications Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
OMAP5910JGZG1 制造商:Texas Instruments 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*