參數資料
型號： MT48LC2M32B2
廠商： Micron Technology, Inc.
英文描述： SYNCHRONOUS DRAM
中文描述： 同步DRAM
文件頁數： 29/53頁
文件大?。?/td> 1818K
代理商： MT48LC2M32B2
29
64Mb: x32 SDRAM
64MSDRAMx32_5.p65 – Rev. B; Pub. 6/02
Micron Technology, Inc., reserves the right to change products or specifications without notice.
2002, Micron Technology, Inc.
64Mb: x32
SDRAM
NOTE (continued):
4. AUTO REFRESH, SELF REFRESH, and LOAD MODE REGISTER commands may only be issued when all
banks are idle.
5. A BURST TERMINATE command cannot be issued to another bank; it applies to the bank represented
by the current state only.
6. All states and sequences not shown are illegal or reserved.
7. READs or WRITEs to bank
m
listed in the Command (Action) column include READs or WRITEs with
auto precharge enabled and READs or WRITEs with auto precharge disabled.
8. CONCURRENT AUTO PRECHARGE: Bank
n
will initiate the auto precharge command when its burst has
been interrupted by bank
m
’s burst.
9. Burst in bank
n
continues as initiated.
10. For a READ without auto precharge interrupted by a READ (with or without auto precharge), the
READ to bank
m
will interrupt the READ on bank
n
, CAS latency later (Figure 7).
11. For a READ without auto precharge interrupted by a WRITE (with or without auto precharge), the
WRITE to bank
m
will interrupt the READ on bank
n
when registered (Figures 9 and 10). DQM should
be used one clock prior to the WRITE command to prevent bus contention.
12. For a WRITE without auto precharge interrupted by a READ (with or without auto precharge), the
READ to bank
m
will interrupt the WRITE on bank
n
when registered (Figure 17), with the data-out
appearing CAS latency later. The last valid WRITE to bank
n
will be data-in registered one clock prior
to the READ to bank
m
.
13. For a WRITE without auto precharge interrupted by a WRITE (with or without auto precharge), the
WRITE to bank
m
will interrupt the WRITE on bank
n
when registered (Figure 15). The last valid WRITE
to bank
n
will be data-in registered one clock prior to the READ to bank
m
.
14. For a READ with auto precharge interrupted by a READ (with or without auto precharge), the READ to
bank
m
will interrupt the READ on bank
n
, CAS latency later. The PRECHARGE to bank
n
will begin
when the READ to bank
m
is registered (Figure 24).
15. For a READ with auto precharge interrupted by a WRITE (with or without auto precharge), the
WRITE to bank
m
will interrupt the READ on bank
n
when registered. DQM should be used two
clocks prior to the WRITE command to prevent bus contention. The PRECHARGE to bank
n
will
begin when the WRITE to bank
m
is registered (Figure 25).
16. For a WRITE with auto precharge interrupted by a READ (with or without auto precharge), the READ
to bank
m
will interrupt the WRITE on bank
n
when registered, with the data-out appearing CAS
latency later. The PRECHARGE to bank
n
will begin after
t
WR is met, where
t
WR begins when the
READ to bank
m
is registered. The last valid WRITE to bank
n
will be data-in registered one clock prior
to the READ to bank
m
(Figure 26).
17. For a WRITE with auto precharge interrupted by a WRITE (with or without auto precharge), the WRITE
to bank
m
will interrupt the WRITE on bank
n
when registered. The PRECHARGE to bank
n
will begin
after
t
WR is met, where
t
WR begins when the WRITE to bank
m
is registered. The last valid WRITE to
bank
n
will be data registered one clock prior to the WRITE to bank
m
(Figure 27).
相關PDF資料
PDF描述
MT48LC32M8A2 SYNCHRONOUS DRAM
MT48LC16M16A2 SYNCHRONOUS DRAM
MT48LC64M4A2 SYNCHRONOUS DRAM
MT48LC4M32B2 SYNCHRONOUS DRAM
MT48LC4M32LFFC SYNCHRONOUS DRAM
相關代理商/技術參數
參數描述
MT48LC2M32B2-6G 制造商:Micron Technology Inc 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*