- 您現在的位置：買賣IC網 > PDF目錄1955 > MPC5553MVR132 (Freescale Semiconductor)MCU 1.5MB FLASH 132MHZ 416-PBGA PDF資料下載
參數資料
| 型號： | MPC5553MVR132 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 6/68頁 |
| 文件大?。?/td> | 0K |
| 描述： | MCU 1.5MB FLASH 132MHZ 416-PBGA |
| 標準包裝： | 200 |
| 系列： | MPC55xx Qorivva |
| 核心處理器： | e200z6 |
| 芯體尺寸： | 32-位 |
| 速度： | 132MHz |
| 連通性： | CAN，EBI/EMI，以太網，SCI，SPI |
| 外圍設備： | DMA，POR，PWM，WDT |
| 輸入/輸出數： | 220 |
| 程序存儲器容量： | 1.5MB（1.5M x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 64K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.35 V ~ 1.65 V |
| 數據轉換器： | A/D 40x12b |
| 振蕩器型： | 外部 |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 416-BBGA |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
MPC5553 Microcontroller Data Sheet, Rev. 4
Electrical Characteristics
Freescale Semiconductor
14
3.7.1
Input Value of Pins During POR Dependent on VDD33
When powering up the device, VDD33 must not lag the latest VDDSYN or RESET power pin (VDDEH6) by
more than the VDD33 lag specification listed in Table 6, spec 8. This avoids accidentally selecting the
bypass clock mode because the internal versions of PLLCFG[0:1] and RSTCFG are not powered and
therefore cannot read the default state when POR negates. VDD33 can lag VDDSYN or the RESET power
pin (VDDEH6), but cannot lag both by more than the VDD33 lag specification. This VDD33 lag specification
applies during power up only. VDD33 has no lead or lag requirements when powering down.
3.7.2
Power-Up Sequence (VRC33 Grounded)
The 1.5 V VDD power supply must rise to 1.35 V before the 3.3 V VDDSYN power supply and the RESET
power supply rises above 2.0 V. This ensures that digital logic in the PLL for the 1.5 V power supply does
not begin to operate below the specified operation range lower limit of 1.35 V. Because the internal 1.5 V
POR is disabled, the internal 3.3 V POR or the RESET power POR must hold the device in reset. Since
they can negate as low as 2.0 V, VDD must be within specification before the 3.3 V POR and the RESET
POR negate.
Figure 3. Power-Up Sequence (VRC33 Grounded)
3.7.3
Power-Down Sequence (VRC33 Grounded)
The only requirement for the power-down sequence with VRC33 grounded is if VDD decreases to less than
its operating range, VDDSYN or the RESET power must decrease to less than 2.0 V before the VDD power
increases to its operating range. This ensures that the digital 1.5 V logic, which is reset only by an ORed
POR and can cause the 1.5 V supply to decrease less than its specification value, resets correctly. See
Table 6, footnote 1.
VDDSYN and RESET Power
VDD
2.0 V
1.35 V
VDD must reach 1.35 V before VDDSYN and the RESET power reach 2.0 V
相關PDF資料 |
PDF描述 |
|---|---|
| MPC555LFMZP40 | IC MCU 32BIT 40MHZ 272-BGA |
| MPC5565MVZ132 | MCU 2MB FLASH 132MHZ 324-PBGA |
| MPC5566MVR132 | MCU 3MB FLASH 132MHZ 416-PBGA |
| MPC561CVR40 | IC MPU 32BIT 40MHZ 388-PBGA |
| MPC562CZP40 | IC MPU 32BIT W/CODE COMP 388PBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC5553MVR132R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontroller |
| MPC5553MVR80 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontroller Data Sheet |
| MPC5553MVR80R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontroller |
| MPC5553MVZ112 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontroller |
| MPC5553MVZ112R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。