- 您現在的位置：買賣IC網 > PDF目錄296559 > MIC2591B-5YTQ (MICREL INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48 PDF資料下載
參數資料
| 型號： | MIC2591B-5YTQ |
| 廠商： | MICREL INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP48 |
| 封裝： | LEAD FREE, TQFP-48 |
| 文件頁數： | 15/34頁 |
| 文件大?。?/td> | 1920K |
| 代理商： | MIC2591B-5YTQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
MIC2591B
Micrel
March 2005
22
M9999-033105
target address, with the R/W bit (LSB) set to the low (write)
state,followedbyacommandbyteandadatabyte.TheSMBus
Read_Byte operation is similar, but is a composite write and
readoperation:thehostrstsendsthedevice’stargetaddress
followed by the command byte, as in a write operation. A new
“Start” bit must then be sent to the MIC2591B, followed by a
repeat of the device address with the R/W bit set to the high
(read) state. The data to be read from the part may then be
clocked out. There is one exception to this rule: If the location
latched in the pointer register from the last write operation is
known to be correct (i.e., points to the desired register within
the MIC2591B), then the “Receive_Byte” procedure may be
used. To perform a Receive_Byte operation, the host sends
an address byte to select the target MIC2591B, with the R/W
bit set to the high (read) state, and then retrieves the data
byte. Figures 10 through 12 show the formats for these data
read and data write procedures.
The Command Register is eight bits (one byte) wide. This
byte carries the address of the MIC2591B’s register to be
operated upon. The command byte values corresponding to
the various MIC2591B register addresses are shown in Table
2. Command byte values other than 0000 0XXXb = 00h - 07h
are reserved and should not be used.
MIC2591B SMBus Address Conguration
The MIC2591B responds to its own unique SMBus address,
which is assigned using A2, A1, and A0. These represent
the 3 LSBs of its 7-bit address, as shown in Table 3. These
address bits are assigned only during power up of the
VSTBY[A/B] supply input. These address bits allow up to
eight MIC2591B devices in a single system. These pins are
either grounded or left unconnected to specify a logical 0 or
logical 1, respectively. A pin designated as a logical 1 may
also be pulled up to VSTBY.
STBY
S 1 0 0 0 A2 A1 A0 0 A 0 0 0 0 0 0 X X A
D4
D5
D6
D3 D2 D1 D0
D7
A P
MIC2591B Device Address
DATA
CLK
Command Byte to MIC2591B
Data Byte to MIC2591B
START
STOP
R/W = WRITE
ACKNOWLEDGE
Master to device transfer,
i.e., DATA driven by master.
Device to master transfer,
i.e., DATA driven by device.
Figure 10. WRITE_BYTE Protocol
S 1 0 0 0 A2 A1 A0
A2 A1 A0
0 A 0 0 0 0 0 0 X X A S 1
0
1
0 0
D4
D5
D6
D3 D2 D1 D0
A D7
/A P
MIC2591B Device Address
DATA
CLK
Command Byte to MIC2591B
MIC2591B Device Address
Data Read From MIC2591B
START
STOP
R/W = WRITE
R/W = READ
ACKNOWLEDGE
ACKNOWLEDGE NOT ACKNOWLEDGE
Master to device transfer,
i.e., DATA driven by master.
Device to master transfer,
i.e., DATA driven by device.
Figure 11. READ_BYTE Protocol
S 1 0 0 0 A2 A1 A0 1 A
D4
D5
D6
D3 D2 D1 D0
D7
/A P
MIC2591B Device Address
DATA
CLK
Byte Read from MIC2591B
START
STOP
R/W = READ
ACKNOWLEDGE NOT ACKNOWLEDGE
Master to device transfer,
i.e., DATA driven by master.
Device to master transfer,
i.e., DATA driven by device.
Figure 12. RECEIVE_BYTE Protocol
相關PDF資料 |
PDF描述 |
|---|---|
| MIC30711-5100W-LF3 | 32 CONTACT(S), FEMALE, RIGHT ANGLE TELECOM AND DATACOM CONNECTOR, SOLDER |
| MIC3730-1.8BR | 1.8 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PSSO5 |
| MIC5225-1.5YM5TR | 1.5 V FIXED POSITIVE LDO REGULATOR, 0.45 V DROPOUT, PDSO5 |
| MIC5225-2.5YM5TR | 2.5 V FIXED POSITIVE LDO REGULATOR, 0.45 V DROPOUT, PDSO5 |
| MIC5225-3.3YM5TR | 3.3 V FIXED POSITIVE LDO REGULATOR, 0.45 V DROPOUT, PDSO5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2592B-2BTQ | 功能描述:IC CTRLR HOTPLUG PCI DUAL 48TQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2592B-2BTQ TR | 功能描述:IC PCI HOT PLUG CTLR DUAL 48TQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2592B-2YTQ | 功能描述:熱插拔功率分布 Dual-slot PCI-Express Hot Swap Power Controller - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2592B-2YTQ TR | 功能描述:熱插拔功率分布 Dual-slot PCI-Express Hot Swap Power Controller - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2593-2BTQ | 功能描述:IC CTRLR HOTPLUG PCI DUAL 48TQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。