參數資料
型號: MAX192BMJP
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: ADC
英文描述: Low-Power, 8-Channel, Serial 10-Bit ADC
中文描述: 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, CDIP20
封裝: CERDIP-20
文件頁數: 19/24頁
文件大?。?/td> 201K
代理商: MAX192BMJP
Layout, Grounding, Bypassing
For best performance, use printed circuit boards.
Wire-wrap boards are not recommended. Board layout
should ensure that digital and analog signal lines are
separated from each other. Do not run analog and digi-
tal (especially clock) lines parallel to one another, or
digital lines underneath the ADC package.
Figure 18 shows the recommended system ground
connections. A single-point analog ground (“star”
ground point) should be established at AGND, sepa-
rate from the logic ground. All other analog grounds
and DGND should be connected to this ground. No
other digital system ground should be connected to
this single-point analog ground. The ground return to
the power supply for this ground should be low imped-
ance and as short as possible for noise-free operation.
High-frequency noise in the V
DD
power supply may
affect the high-speed comparator in the ADC. Bypass
these supplies to the single-point analog ground with
0.1μF and 4.7μF bypass capacitors close to the
MAX192. Minimize capacitor lead lengths for best sup-
ply-noise rejection. If the +5V power supply is very
noisy, a 10
resistor can be connected as a lowpass
filter, as shown in Figure 18.
High-S peed Digital Interfac ing
The MAX192 can interface with QSPI at high through-
put rates using the circuit in Figure 19. This QSPI circuit
can be programmed to do a conversion on each of the
eight channels. The result is stored in memory without
taxing the CPU since QSPI incorporates its own
micro-sequencer.
Figure 20 details the code that sets up QSPI for
autonomous operation. In external clock mode, the
MAX192 performs a single-ended, unipolar conversion
on each of the eight analog input channels. Figure 21
shows the timing associated with the assembly code of
Figure 20. The first byte clocked into the MAX192 is the
control byte, which triggers the first conversion on CH0.
The last two bytes clocked into the MAX192 are all
zero, and clock out the results of the CH7 conversion.
M
Low-Power, 8-Channel,
S erial 10-Bit ADC
______________________________________________________________________________________
19
+5V
510k
100k
24k
0.01
μ
F
12
REFADJ
MAX192
Figure 17. Reference-Adjust Circuit
+5V
GND
SUPPLIES
DGND
+5V
DGND
AGND
V
DD
DIGITAL
CIRCUITRY
MAX192
R* = 10
* OPTIONAL
Figure 18. Power-Supply Grounding Connection
相關PDF資料
PDF描述
MAX192AEWP Low-Power, 8-Channel, Serial 10-Bit ADC
MAX192BEWP Low-Power, 8-Channel, Serial 10-Bit ADC
MAX192BCPP Low-Power, 8-Channel, Serial 10-Bit ADC
MAX192BCWP ECONOLINE: RJ & RG - Dual Output from a Single Input Rail - 3kVDC & 4kVDC Isolation - Optional Continuous Short Circuit Protected - Custom Solutions Available - UL94V-0 Package Material - Efficiency to 84%
MAX1940 Triple USB Switch with Autoreset and Fault Blanking
相關代理商/技術參數
參數描述
MAX192BMWP/PR 制造商:Maxim Integrated Products 功能描述:- Rail/Tube
MAX1930ESA 功能描述:電源開關 IC - USB 1A Crnt-Ltd Switch for 2 USB Ports RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube
MAX1930ESA+ 功能描述:電源開關 IC - USB 1A Crnt-Ltd Switch for 2 USB Ports RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube
MAX1930ESA+T 功能描述:電源開關 IC - USB 1A Crnt-Ltd Switch for 2 USB Ports RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube
MAX1930ESA-T 功能描述:電源開關 IC - USB 1A Crnt-Ltd Switch for 2 USB Ports RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube