- 您現在的位置：買賣IC網 > PDF目錄383341 > MAX192BMJP (MAXIM INTEGRATED PRODUCTS INC) Low-Power, 8-Channel, Serial 10-Bit ADC PDF資料下載
參數資料
| 型號： | MAX192BMJP |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | Low-Power, 8-Channel, Serial 10-Bit ADC |
| 中文描述： | 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, CDIP20 |
| 封裝： | CERDIP-20 |
| 文件頁數： | 12/24頁 |
| 文件大?。?/td> | 201K |
| 代理商： | MAX192BMJP |
M
Low-Power, 8-Channel,
S erial 10-Bit ADC
12
______________________________________________________________________________________
SSTRB
CS
SCLK
DIN
DOUT
1
4
8
12
16
20
24
START
SEL2 SEL1 SEL0
BIP
DIF
PD1
PD0
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
S1
SO
ACQUISITION
1.5μs (CLK = 2MHz)
IDLE
FILLED WITH
ZEROS
IDLE
CONVERSION
t
ACQ
A/D STATE
RB1
RB1
RB2
RB3
RB2
RB3
CS
SCLK
DIN
DOUT
t
CSH
t
CSS
t
CL
t
DS
t
DH
t
DV
t
CH
t
DO
t
TR
t
CSH
Figure 6. 24-Bit External Clock Mode Conversion Timing (SPI, QSPI and Microwire Compatible)
Figure 7. Detailed Serial-Interface Timing
Pulling
CS
high prevents data from being clocked into
the MAX192 and three-states DOUT, but it does not
adversely affect an internal clock-mode conversion
already in progress. When internal clock mode is
selected, SSTRB does not go into a high-impedance
state when
CS
goes high.
Figure 10 shows the SSTRB timing in internal clock
mode. In internal clock mode, data can be shifted in
and out of the MAX192 at clock rates exceeding
4.0MHz, provided that the minimum acquisition time,
t
AZ
, is kept above 1.5μs.
Data Framing
The falling edge of
CS
does
not
start a conversion on
the MAX192. The first logic high clocked into DIN is inter-
preted as a start bit and defines the first bit of the control
byte. A conversion starts on the falling edge of SCLK,
after the eighth bit of the control byte (the PD0 bit) is
clocked into DIN. The start bit is defined as:
The first high bit clocked into DIN with
CS
low any-
time the converter is idle, e.g. after V
DD
is applied.
OR
The first high bit clocked into DIN after bit 3 of a
conversion in progress is clocked onto the DOUT pin.
If a falling edge on
CS
forces a start bit before bit 3
(B3) becomes available, then the current conversion
will be terminated and a new one started. Thus, the
fastest the MAX192 can run is 15 clocks per conver-
sion. Figure 11a shows the serial-interface timing nec-
essary to perform a conversion every 15 SCLK cycles
in external clock mode. If
CS
is low and SCLK is contin-
uous, guarantee a start bit by first clocking in 16 zeros.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX192AEWP | Low-Power, 8-Channel, Serial 10-Bit ADC |
| MAX192BEWP | Low-Power, 8-Channel, Serial 10-Bit ADC |
| MAX192BCPP | Low-Power, 8-Channel, Serial 10-Bit ADC |
| MAX192BCWP | ECONOLINE: RJ & RG - Dual Output from a Single Input Rail - 3kVDC & 4kVDC Isolation - Optional Continuous Short Circuit Protected - Custom Solutions Available - UL94V-0 Package Material - Efficiency to 84% |
| MAX1940 | Triple USB Switch with Autoreset and Fault Blanking |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX192BMWP/PR | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX1930ESA | 功能描述:電源開關 IC - USB 1A Crnt-Ltd Switch for 2 USB Ports RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX1930ESA+ | 功能描述:電源開關 IC - USB 1A Crnt-Ltd Switch for 2 USB Ports RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX1930ESA+T | 功能描述:電源開關 IC - USB 1A Crnt-Ltd Switch for 2 USB Ports RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX1930ESA-T | 功能描述:電源開關 IC - USB 1A Crnt-Ltd Switch for 2 USB Ports RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。