參數資料
型號： M37736EHLXXXHP
廠商： Mitsubishi Electric Corporation
英文描述： PROM VERSION OF M37736MHLXXXHP(MICROCOMPUTERS)
中文描述： PROM的版本M37736MHLXXXHP（微型）
文件頁數： 20/96頁
文件大?。?/td> 1328K
代理商： M37736EHLXXXHP
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
MITSUBISHI MICROCOMPUTERS
M37736MHBXXXGP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
20
(2) Event counter mode [01]
Figure 17 shows the bit configuration of the timer Ai mode register
during the event counter mode. In the event counter mode, the bit 0
of the timer Ai mode register must be “1” and bits 1 and 5 must be
“0”.
The input signal from the TAi
IN
pin is counted when the count start
flag shown in Figure 15 is “1” and counting is stopped when it is “0”.
Count is performed at the fall of the input signal when bit 3 is “0” and
at the rise of the signal when it is “1”.
In the event counter mode, whether to increment or decrement the
count can be selected with the up-down flag or the input signal from
the TAi
OUT
pin.
When bit 4 of the timer Ai mode register is “0”, the up-down flag is
used to determine whether to increment or decrement the count
(decrement when the flag is “0” and increment when it is “1”). Figure
18 shows the bit configuration of the up-down flag.
When bit 4 of the timer Ai mode register is “1”, the input signal from
the TAi
OUT
pin is used to determine whether to increment or decrement
the count. However, note that bit 2 must be “0” if bit 4 is “1”. Because
TAi
OUT
pin becomes an output pin with pulse output if bit 2 is “1”.
The count is decremented when the input signal from the TAi
OUT
pin
is “L” and incremented when it is “H”. Determine the level of the input
signal from the TAi
OUT
pin before an effective edge is input to the
TAi
IN
pin.
An interrupt request signal is generated and the interrupt request bit
of the timer Ai interrupt control register is set when the counter reaches
0000
16
(decrement count) or FFFF
16
(increment count). At the same
time, timers A0 and A1 transfer the contents of the reload register to
the counter and continue counting.
Timers A2, A3, and A4 transfer the contents of the reload register to
the counter and continue count when bit 6 of the corresponding timer
Ai mode register is “0”, but when bit 6 is “1”, they continue counting
without transferring the contents of the reload register to the counter.
When bit 2 is “1”, the waveform of which polarity is reversed each
time the counter reaches 0000
16
(decrement count) or FFFF
16
(increment count) is output from TAi
OUT
pin. If bit 2 is “0”, the TAi
OUT
pin can be used as a normal port pin. However, if bit 4 is “1” and the
TAi
OUT
pin is used as an output pin, the output from the TAi
OUT
pin
changes the count direction. Therefore, bit 4 must be “0” unless the
output from the TAi
OUT
pin is used to select the count direction.
Data write and data read are performed in the same way as for the
timer mode. That is, when data is written to timer Ai which is halted,
it is also written to the reload register and the counter.
When data is written to timer Ai which is busy, the data is written to
the reload register, but not the counter. The counter is reloaded with
new data from the reload register at the next reload time and continues
counting. For timers A2, A3, and A4, the contents of the reload register
is not reloaded in the counter when bit 6 of the corresponding timer
Ai mode register is “1”. The contents of the counter can be read at
any time.
Fig. 18 Up-down flag bit configuration
Fig. 17 Timer Ai mode register bit configuration during event counter
mode
Timer A0 up-down flag
Timer A1 up-down flag
Timer A2 up-down flag
Timer A3 up-down flag
7 6
5
4 3
2
1 0
44
16
Addresses
Up-down flag
Timer A4 up-down flag
Timer A3 two-phase pulse signal processing
selection bit
0 : Two-phase pulse signal processing disabled
1 : Two-phase pulse signal processing mode
Timer A2 two-phase pulse signal processing
selection bit
0 : Two-phase pulse signal processing disabled
1 : Two-phase pulse signal processing mode
Timer A4 two-phase pulse signal processing
selection bit
0 : Two-phase pulse signal processing disabled
1 : Two-phase pulse signal processing mode
This bit is available for timer A3.
0 : Two-phase pulse signal processing
in the same manner as timer A2
1 : Two-phase pulse signal processing
in the same manner as timer A4
0 1 : Always “01” in event counter
mode
7 6
5
4 3
2
1 0
0
0 1
0 : No pulse output
1 : Pulse output
0 : Count at the falling edge of input
signal
1 : Count at the rising edge of input
signal
0 : Increment or decrement according
to up-down flag
1 : Increment or decrement according
to TAi
OUT
pin input signal level
0 : Always “0” in event counter mode
This bit is available for times A2, A3,
and A4.
0 : Reload
1 : No reload
Timer A0 mode register 56
16
Timer A1 mode register 57
16
Timer A2 mode register 58
16
Timer A3 mode register 59
16
Timer A4 mode register 5A
16
Addresses
相關PDF資料
PDF描述
M37736MHLXXXHP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37736EHBXXXGP PROM VERSION OF M37736MHBXXXGP(MICROCOMPUTERS)
M37736MHBXXXGP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37753FFCFP SINGLE CHIP 16 BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
M37753FFCHP SINGLE CHIP 16 BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
相關代理商/技術參數
參數描述
M37736M4B 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37736M4BXXXGP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37736M4L 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37736M4LXXXHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37736MHB 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*