參數資料
型號: M34584EDFP
元件分類: 微控制器/微處理器
英文描述: 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42
封裝: 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-42
文件頁數: 98/157頁
文件大?。?/td> 1130K
代理商: M34584EDFP
Rev.3.00
2004.08.06
page 45 of 155
REJ03B0010-0300Z
4584 Group
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
WATCHDOG TIMER
Watchdog timer provides a method to reset the system when a pro-
gram run-away occurs. Watchdog timer consists of timer
WDT(16-bit binary counter), watchdog timer enable flag (WEF),
and watchdog timer flags (WDF1, WDF2).
The timer WDT downcounts the instruction clocks as the count
source from “FFFF16” after system is released from reset.
After the count is started, when the timer WDT underflow occurs
(after the count value of timer WDT reaches “000016,” the next
count pulse is input), the WDF1 flag is set to “1.”
If the WRST instruction is never executed until the timer WDT un-
derflow occurs (until timer WDT counts 65534), WDF2 flag is set to
“1,” and the RESET pin outputs “L” level to reset the microcom-
puter.
Execute the WRST instruction at each period of 65534 machine
cycle or less by software when using watchdog timer to keep the
microcomputer operating normally.
When the WEF flag is set to “1” after system is released from reset,
the watchdog timer function is valid.
When the DWDT instruction and the WRST instruction are ex-
ecuted continuously, the WEF flag is cleared to “0” and the
watchdog timer function is invalid.
The WEF flag is set to "1" at system reset or RAM back-up mode.
The WRST instruction has the skip function. When the WRST in-
struction is executed while the WDF1 flag is “1”, the WDF1 flag is
cleared to “0” and the next instruction is skipped.
When the WRST instruction is executed while the WDF1 flag is “0”,
the next instruction is not skipped.
The skip function of the WRST instruction can be used even when
the watchdog timer function is invalid.
Fig. 32 Watchdog timer function
65534 count
(Note)
Value of 16-bit timer (WDT)
WDF1 flag
WRST instruction
executed
(skip executed)
RESET pin output
WDF2 flag
System reset
Reset
released
After system is released from reset (= after program is started), timer WDT starts count down.
When timer WDT underflow occurs, WDF1 flag is set to “1.”
When the WRST instruction is executed, WDF1 flag is cleared to “0,” the next instruction is skipped.
When timer WDT underflow occurs while WDF1 flag is “1,” WDF2 flag is set to “1” and the
watchdog reset signal is output.
The output transistor of RESET pin is turned “ON” by the watchdog reset signal and system reset is
executed.
Note: The number of count is equal to the number of cycle because the count source of watchdog timer
is the instruction clock.
FFFF16
000016
相關PDF資料
PDF描述
M35047-XXXSP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDIP20
M35047-XXXFP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20
M35048-001FP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20
M35049-XXXFP 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20
M35053-XXXFP 24 X 10 CHARACTERS CRT CHAR DSPL CTLR, PDSO20
相關代理商/技術參數
參數描述
M34584MD-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
M3459 功能描述:電纜固定件和配件 RLTCG 3/8 NPT GRAY NO NUT RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度:
M3460 功能描述:電纜固定件和配件 RLTCG 3/4 NPT BLACK NO NUT RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度:
M3460-3R9-083 制造商:Bonitron 功能描述:REGULATOR FOR VFDS
M3460B-E130-R2-DDM-P3 制造商:Bonitron 功能描述:UNDERVOLTAGE RIDE-THRU PRODUCT