- 您現在的位置：買賣IC網 > PDF目錄45026 > M32180F8VFP 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP240 PDF資料下載
參數資料
| 型號： | M32180F8VFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP240 |
| 封裝： | 32 X 32 MM, 0.50 MM PITCH, PLASTIC, QFP-240 |
| 文件頁數： | 31/139頁 |
| 文件大小： | 3774K |
| 代理商： | M32180F8VFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁
5
5-15
INTERRUPT CONTROLLER (ICU)
32180 Group User’s Manual (Rev.1.0)
5.5.2 Processing by Internal Peripheral I/O Interrupt Handlers
(1) Branching to the interrupt handler
Upon accepting an interrupt request, the CPU branches to the EIT vector entry after performing the hardware
preprocessing as described in Section 4.3, “EIT Processing Procedure.” The EIT vector entry for External
Interrupt (EI) is located at the address H’0000 0080. This address is where the instruction (not the jump
address itself) for branching to the beginning of the interrupt handler routine for external interrupt requests is
written.
(2) Processing in the External Interrupt (EI) handler
A typical operation of the External Interrupt (EI) handler (for interrupts from internal peripheral I/O) is shown
in Figure 5.5.2.
[1] Saving each register to the stack
Save the BPC, PSW and general-purpose registers to the stack. Also, save the accumulator and FPSR
register to the stack as necessary.
[2] Reading the Interrupt Request Mask Register (IMASK) and saving to the stack
Read the Interrupt Request Mask Register and save its content to the stack.
[3] Reading the Interrupt Vector Register (IVECT)
Read the Interrupt Vector Register. This register holds the 16 low-order address bits of the ICU vector table
for the accepted interrupt request source that was stored in it when accepting an interrupt request. When the
Interrupt Vector Register is read, the following processing is automatically performed in hardware:
The interrupt priority level of the accepted interrupt request (ILEVEL) is set in the IMASK register as a
new IMASK value. (Interrupts with lower priority levels than that of the accepted interrupt request
source are masked.)
The accepted interrupt request source is cleared (not cleared for level-recognized interrupt request
sources).
The interrupt request (EI) to the CPU core is dropped.
The ICU’s internal sequencer is activated to start internal processing (interrupt priority resolution).
[4] Reading and overwriting the Interrupt Request Mask Register (IMASK)
Read the Interrupt Request Mask Register and overwrite it with the read value. This write to the IMASK
register causes the following processing to be automatically performed in hardware:
The interrupt request (EI) to the CPU core is dropped.
The ICU’s internal sequencer is activated to start internal processing (interrupt priority resolution).
Note: Processing in [4] here is unnecessary when multiple interrupts are to be enabled in [6] below.
[5] Reading the ICU vector table
Read the ICU vector table for the accepted interrupt request source. The relevant ICU vector table
address can be obtained by zero-extending the content of the Interrupt Vector Register that was read in
[3] (i.e., the 16 low-order address bits of the ICU vector table for the accepted interrupt request source).
The ICU vector table must have set in it the start address of the interrupt handler for the interrupt request
source concerned.)
[6] Enabling multiple interrupts
To enable another higher priority interrupt while processing the accepted interrupt (i.e., enabling multiple
interrupts), set the PSW register IE bit to "1".
[7] Branching to the internal peripheral I/O interrupt handler
Branch to the start address of the interrupt handler that was read out in [5].
[8] Processing in the internal peripheral I/O interrupt handler
[9] Disabling interrupts
Clear the PSW register IE bit to "0" to disable interrupts.
5.5 Description of Interrupt Operation
相關PDF資料 |
PDF描述 |
|---|---|
| M32182F3VFP | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP144 |
| M32182F3UFP | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144 |
| M32182F3TFP | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144 |
| M32182F3VFP | 32-BIT, FLASH, 64 MHz, RISC MICROCONTROLLER, PQFP144 |
| M32182F3TFP | 32-BIT, FLASH, 80 MHz, RISC MICROCONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M32180T2-PTC | 功能描述:DEV CONNECTION CNVTR FOR 32180 G RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF) |
| M32182F3TFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:32-BIT RISC SINGLE-CHIP MICROCOMPUTER M32R FAMILY / M32R/ECU SERIES |
| M32182F3UFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:32-BIT RISC SINGLE-CHIP MICROCOMPUTER M32R FAMILY / M32R/ECU SERIES |
| M32182F3VFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:32-BIT RISC SINGLE-CHIP MICROCOMPUTER M32R FAMILY / M32R/ECU SERIES |
| M32182F8TFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:32-BIT RISC SINGLE-CHIP MICROCOMPUTER M32R FAMILY / M32R/ECU SERIES |
發布緊急采購，3分鐘左右您將得到回復。