參數資料
型號: M25PE40VMW6G
廠商: STMICROELECTRONICS
元件分類: PROM
英文描述: 512K X 8 SPI BUS SERIAL EEPROM, PDSO8
封裝: 0.208 INCH, ROHS COMPLIANT, PLASTIC, SOP-8
文件頁數: 17/62頁
文件大?。?/td> 565K
代理商: M25PE40VMW6G
Instructions
M25PE40
6.4
Read Status Register (RDSR)
The Read Status Register (RDSR) instruction allows the Status Register to be read. The
Status Register may be read at any time, even while a Program, Erase or Write cycle is in
progress. When one of these cycles is in progress, it is recommended to check the Write In
Progress (WIP) bit before sending a new instruction to the device. It is also possible to read
the Status Register continuously, as shown in Figure 10.
The status bits of the Status Register are as follows:
6.4.1
WIP bit
The Write In Progress (WIP) bit indicates whether the memory is busy with a Write, Program
or Erase cycle. When set to ‘1’, such a cycle is in progress, when reset to ‘0’ no such cycle is
in progress.
6.4.2
WEL bit
The Write Enable Latch (WEL) bit indicates the status of the internal Write Enable Latch.
When set to ‘1’ the internal Write Enable Latch is set, when set to ‘0’ the internal Write
Enable Latch is reset and no Write, Program or Erase instruction is accepted.
6.4.3
BP2, BP1, BP0 bits
The Block Protect bits (BP2, BP1, BP0) are non-volatile. They define the size of the area to
be software protected against Program and Erase instructions. These bits are written with
the Write Status Register (WRSR) instruction. When one or more of the Block Protect (BP2,
BP1, BP0) bits is set to ‘1’, the relevant memory area (as defined in Table 3) becomes
protected against Page Program (PP), Page Erase (PE), Sector Erase (SE) and Subsector
Erase (SSE) instructions. The Block Protect (BP2, BP1, BP0) bits can be written provided
that the Hardware Protected mode has not been set. The Bulk Erase (BE) instruction is
executed if, and only if:
all Block Protect (BP2, BP1, BP0) bits are 0
the Lock Register protection bits are not all set (‘1’).
6.4.4
SRWD bit
The Status Register Write Disable (SRWD) bit is operated in conjunction with the Write
Protect (W) signal. When the Status Register Write Disable (SRWD) bit is set to ‘1’, and
Write Protect (W) is driven Low, the non-volatile bits of the Status Register (SRWD, BP2,
BP1, BP0) become read-only bits. In such a state, as the Write Status Register (WRSR)
instruction is no longer accepted for execution, the definition of the size of the Write
Protected area cannot be further modified.
Table 7.
Status Register format(1)(2)(3)
1.
WEL (Write Enable Latch) and WIP ((Write In Program) are volatile read-only bits (WEL is set and reset by
specific instructions; WIP is automatically set and reset by the internal logic of the device).
2.
SRWD = Status Register Write Protect bit; BP0, BP1, BP2 = Block Protect bits.
3.
The BP bits and the SRWD bit exist only in the T9HX process.
b7
b0
SRWD
0
BP2
BP1
BP0
WEL
WIP
相關PDF資料
PDF描述
M27C1024-10F1X 1 Mbit 64Kb x16 UV EPROM and OTP EPROM
M27C1024-10F3TR 1 Mbit 64Kb x16 UV EPROM and OTP EPROM
M27C1024-10F3X 1 Mbit 64Kb x16 UV EPROM and OTP EPROM
M27C1024-10F6TR 1 Mbit 64Kb x16 UV EPROM and OTP EPROM
M27C1024-10F6X 1 Mbit 64Kb x16 UV EPROM and OTP EPROM
相關代理商/技術參數
參數描述
M25PE40-VMW6G 功能描述:閃存 4 Mbit Lo Vltg Page Erasable Seral 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M25PE40-VMW6G_NUD 制造商:Micron Technology Inc 功能描述:
M25PE40VMW6P 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit, low voltage, Page-Erasable Serial Flash memory with byte alterability, 50 MHz SPI bus, standard pinout
M25PE40-VMW6P 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:4 Mbit, page-erasable serial Flash memory with byte alterability, 75 MHz SPI bus, standard pinout
M25PE40VMW6TG 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit, low voltage, Page-Erasable Serial Flash memory with byte alterability, 50 MHz SPI bus, standard pinout