參數資料
型號： LM2633
廠商： National Semiconductor Corporation
英文描述： Advanced Two-Phase Synchronous Triple Regulator Controller for Notebook CPUs
中文描述： 先進的兩相同步三穩壓控制器用于筆記本處理器
文件頁數： 36/40頁
文件大?。?/td> 1350K
代理商： LM2633
Control Loop Design
(Continued)
amplifier, and I
is the current drawn by the FB2 pin. The
V
and I
fb2
have a typical value of 1.24V and 18 nA
respectively.
Example: V
out2
= 1.5V, R
1
= 10 k
.
(51)
To calculate the total system tolerance, use the following
equation:
(52)
where
φ
is the tolerance of the Channel 2 reference voltage,
and
σ
is the tolerance of the resistors.
Example: V
out2
= 3.3V, feedback resistors have a
±
1%
tolerance.
(53)
That means the 3.3V output voltage will have a
±
2.96%
tolerance over the (LM2633 die) temperature range of 0C to
125C.
Channel 2 output voltage should not go above 6V in
pulse-skip mode. That is because the SENSE2 pin cannot
take a voltage higher than 6V. However, if force-PWM op-
eration is the chosen operating mode, then the SENSE2 pin
can be grounded and there will be no limitation to Channel 2
output voltage.
If the desired Channel 1 voltage is higher than 2V, an
op-amp and a voltage divider can be used to expand the
voltage range, as shown in Figure 18
It is recommended that the VIDx pins be all tied to ground so
that the DAC is set at 2.00V. That will reduce the total
tolerance. The equations used to calculate Channel 2’s feed-
back resistors and total tolerance still hold, except that the
reference voltage V
is 2.00V instead of 1.24V. Channel 1
can operate only in force-PWM mode when it is configured
as Figure 18
Since an op-amp is an active device, pay close attention to
its start up and shut down behavior. Make sure that it does
not create a problem during those times.
Designing a Power Supply without a Load Transient
Specification
Many times the load transient response of a buck regulator is
not a critical issue. In that case, the selection of the power
stage components can start from the inductor ripple current.
Choosing the peak-to-peak ripple current to be 30% of the
maximum load current is often a good starting point. Then
the inductance value can be determined by ripple, switching
frequency and input and output voltages. By rearranging
Equation (13) the inductance value can be calculated as
follows:
(54)
Example: V
in_max
= 21V, V
n
= 1.6V, I
load_max
= 10A.
The output capacitors can be chosen based on the output
voltage ripple requirement. If there is no specific require-
ment, then a
±
1% ripple level may be a good starting point.
The equation for determining the impedance of the output
capacitors is:
(55)
If the ESR zero frequency of the capacitor is lower than the
switching frequency, such as the case of aluminum, tantalum
and OSCON capacitors, then the output capacitors are cho-
sen by the ESR value. Otherwise, such as in the case of
ceramic capacitors, the output capacitors are chosen by the
capacitance. The equation is:
(56)
Basically make sure that the product of the impedance of the
capacitors and the ripple current does not exceed the ripple
voltage requirement.
Example: V
n
= 1.6V, I
rip
= 3A.
(57)
If ceramic capacitors are preferred, then the minimum ca-
pacitance is:
(58)
200008B6
FIGURE 18. How to Make V
OUT1
Higher Than 2V
L
www.national.com
36
相關PDF資料
PDF描述
LM2633MTD Advanced Two-Phase Synchronous Triple Regulator Controller for Notebook CPUs
LM2647LQX Dual Synchronous Buck Regulator Controller
LM2647MTC Dual Synchronous Buck Regulator Controller
LM2665M6 Switched Capacitor Voltage Converter
LM2665M6X Switched Capacitor Voltage Converter
相關代理商/技術參數
參數描述
LM2633EVAL 功能描述:電源管理IC開發工具 EVAL BOARDFOR LM2633 RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
LM2633MTD 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Advanced Two-Phase Synchronous Triple Regulator Controller for Notebook CPUs
LM2633MTD/NOPB 功能描述:IC REG CTRLR 2-PHS SYNC 48TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)
LM2633MTDX/NOPB 制造商:Texas Instruments 功能描述:5 BIT DAC TRIPLE OUTPUT CONTR
LM2635 制造商:NSC 制造商全稱:National Semiconductor 功能描述:5-Bit Programmable Synchronous Buck Regulator Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*