參數資料
型號: ISP1181DGG
廠商: NXP SEMICONDUCTORS
元件分類: 總線控制器
英文描述: INDUCTOR 4.7NH +-.3NH 0402 SMD
中文描述: UNIVERSAL SERIAL BUS CONTROLLER, PDSO48
封裝: 6.10 MM, PLASTIC, TSSOP-48
文件頁數: 28/69頁
文件大?。?/td> 1655K
代理商: ISP1181DGG
Philips Semiconductors
ISP1181
Full-speed USB interface
Objective specification
Rev. 01 — 13 March 2000
28 of 69
9397 750 06896
Philips Electronics N.V. 2000. All rights reserved.
Table 22: Hardware Configuration Register: bit allocation
Bit
15
Symbol
reserved
EXTPUL
Reset
0
Access
R/W
Bit
7
Symbol
DAKOLY
DRQPOL
Reset
0
Access
R/W
14
13
12
11
10
9
8
NOLAZY
1
R/W
5
DAKPOL
0
R/W
CLKRUN
0
R/W
4
EOTPOL
0
R/W
CKDIV[3:0]
0
0
0
1
1
R/W
6
R/W
3
R/W
2
R/W
1
INTLVL
0
R/W
R/W
0
INTPOL
0
R/W
WKUPCS
0
R/W
PWROFF
1
R/W
1
R/W
Table 23: Hardware Configuration Register: bit description
Bit
Symbol
Description
15
-
reserved
14
EXTPUL
A logic 1 indicates that an external 1.5 k
pull-up resistor is
used on pin D
+
and that SoftConnect is not used. Bus reset
value: unchanged.
13
NOLAZY
A logic 1 disables output on pin CLKOUT of the LazyClock
frequency (24 kHz) during ‘suspend’ state. A logic 0 causes pin
CLKOUT to switch to LazyClock output after approximately 2 ms
delay, following the setting of bit GOSUSP in the Mode Register.
Bus reset value: unchanged.
12
CLKRUN
A logic 1 indicates that the internal clocks are always running,
even during ‘suspend’ state. A logic 0 switches off the internal
oscillator and PLL, when they are not needed. During ‘suspend’
state this bit must be made logic 0 to meet the suspend current
requirements. The clock is stopped after a delay of
approximately 2 ms, following the setting of bit GOSUSP in the
Mode Register. Bus reset value: unchanged.
11 to 8
CKDIV[3:0]
This field specifies the clock division factor N, which controls the
clock frequency on output CLKOUT. The output frequency in
MHz is given by
3 to 48 MHz (N = 0 to 15). with a reset value of 12 MHz (N = 3).
The hardware design guarantees no glitches during frequency
change. Bus reset value: unchanged.
7
DAKOLY
A logic 1 selects DACK-only DMA mode. A logic 0 selects 8237
compatible DMA mode. Bus reset value: unchanged.
6
DRQPOL
Selects DREQ signal polarity (0 = active LOW, 1 = active
HIGH). Bus reset value: unchanged.
5
DAKPOL
Selects DACK signal polarity (0 = active LOW, 1 = active HIGH).
Bus reset value: unchanged.
4
EOTPOL
Selects EOT signal polarity (0 = active LOW, 1 = active HIGH).
Bus reset value: unchanged.
3
WKUPCS
A logic 1 enables remote wake-up via a LOW level on input CS.
Bus reset value: unchanged.
. The clock frequency range is
48
N
1
+
(
)
相關PDF資料
PDF描述
ISP1183 Low-power Universal Serial Bus interface device with DMA
ISP1183BS Low-power Universal Serial Bus interface device with DMA
ISP1301 Universal Serial Bus On-The-Go transceiver
ISP1301BS Universal Serial Bus On-The-Go transceiver
ISP1362 Single-chip Universal Serial Bus On-The-Go controller
相關代理商/技術參數
參數描述
ISP1183 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low-power Universal Serial Bus interface device with DMA
ISP1183BS 功能描述:IC USB HOST CTRL LOW-SPD 32HVQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA,便攜式音頻/視頻,智能電話 接口:I²C,2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤(4x4) 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
ISP1183BS,118 功能描述:USB 接口集成電路 FULL-SPD USB2 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1183BS,151 功能描述:USB 接口集成電路 FULL-SPD USB2 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1183BS,157 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20