參數資料
型號： ISP1181DGG
廠商： NXP SEMICONDUCTORS
元件分類： 總線控制器
英文描述： INDUCTOR 4.7NH +-.3NH 0402 SMD
中文描述： UNIVERSAL SERIAL BUS CONTROLLER, PDSO48
封裝： 6.10 MM, PLASTIC, TSSOP-48
文件頁數： 16/69頁
文件大?。?/td> 1655K
代理商： ISP1181DGG
Philips Semiconductors
ISP1181
Full-speed USB interface
Objective specification
Rev. 01 — 13 March 2000
16 of 69
9397 750 06896
Philips Electronics N.V. 2000. All rights reserved.
In DACK-only mode the ISP1181 uses the DACK signal as data strobe. Input signals
RD and WR are ignored. This mode is used in CPU systems that have a single
address space for memory and I/O access. Such systems have no separate MEMW
and MEMR signals: the RD and WR signals are also used as memory data strobes.
10.4 End-Of-Transfer conditions
10.4.1
Bulk endpoints
A DMA transfer to/from a bulk endpoint can be terminated by any of the following
conditions (bit names refer to the DMA Configuration Register, see
Table 26
):
An external End-Of-Transfer signal occurs on input EOT
The internal DMA Counter Register reaches zero (CNTREN = 1)
A short/empty packet is received on an enabled OUT endpoint (SHORTP = 1)
DMA operation is disabled by clearing bit DMAEN.
External EOT:
When reading from an OUT endpoint, an external EOT will stop the
DMA operation and
clear any remaining data
in the current FIFO. For a double-
buffered endpoint the other (inactive) buffer is not affected.
When writing to an IN endpoint, an EOT will stop the DMA operation and the data
packet in the FIFO (even if it is smaller than the maximum packet size) will be sent to
the USB host at the next IN token.
DMA Counter Register zero:
An EOT from the DMA Counter Register is enabled by
setting bit CNTREN in the DMA Configuration Register. The ISP1181 has a 16-bit
DMA Counter Register, which specifies the number of bytes to be transferred. When
DMA is enabled (DMAEN = 1), the internal DMA counter is loaded with the value from
the DMA Counter Register. When the internal counter reaches zero an EOT condition
is generated and the DMA operation stops.
Short/empty packet:
Normally, the transfer byte count must be set via a control
endpoint before any DMA transfer takes place. When a short/empty packet has been
enabled as EOT indicator (SHORTP = 1), the transfer size is determined by the
presence of a short/empty packet in the data. This mechanism permits the use of a
fully autonomous data transfer protocol.
Fig 4.
ISP1181 in DACK-only DMA mode.
idth
RAM
ISP1181
DMA
CONTROLLER
CPU
DREQ
DACK
HRQ
HLDA
HRQ
HLDA
DREQ
DACK
RD
WR
MGS779
AD,
DATA1 to DATA15
相關PDF資料
PDF描述
ISP1183 Low-power Universal Serial Bus interface device with DMA
ISP1183BS Low-power Universal Serial Bus interface device with DMA
ISP1301 Universal Serial Bus On-The-Go transceiver
ISP1301BS Universal Serial Bus On-The-Go transceiver
ISP1362 Single-chip Universal Serial Bus On-The-Go controller
相關代理商/技術參數
參數描述
ISP1183 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low-power Universal Serial Bus interface device with DMA
ISP1183BS 功能描述:IC USB HOST CTRL LOW-SPD 32HVQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
ISP1183BS,118 功能描述:USB 接口集成電路 FULL-SPD USB2 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1183BS,151 功能描述:USB 接口集成電路 FULL-SPD USB2 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1183BS,157 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*