參數資料
型號： ISP1181
廠商： NXP Semiconductors N.V.
英文描述： Full-speed Universal Serial Bus Interface Device(全速通用串行總線接口器件)
中文描述： 全速通用串行總線接口設備（全速通用串行總線接口器件）
文件頁數： 61/69頁
文件大?。?/td> 1655K
代理商： ISP1181
Philips Semiconductors
ISP1181
Full-speed USB interface
Objective specification
Rev. 01 — 13 March 2000
61 of 69
9397 750 06896
Philips Electronics N.V. 2000. All rights reserved.
20.2 Interfacing ISP1181 with an H8S/2357 microcontroller
This section gives a summary of the ISP1181 interface with a H8S/2357 (or
compatible) microcontroller. Aspects discussed are: interrupt handling, address
mapping, DMA and I/O port usage for suspend and remote wake-up control. A typical
interface circuit is shown in
Figure 35
.
20.2.1
Interrupt Handling
ISP1181
: program the Hardware Configuration register to select an active LOW
level for output INT (INTPOL = 0, see
Table 22
)
H8S/2357
: program the IRQ Sense Control Register (ISCRH and ISCRL) to
specify low-level sensing for the IRQ input.
20.2.2
Address Mapping in H8S/2357
The H8S/2357 bus controller partitions its 16 Mbyte address space into eight areas
(0 to 7) of 2 Mbyte each. The bus controller will activate one of the outputs CS0 to
CS7 when external address space for the associated area is accessed.
The ISP1181 can be mapped to any address area, allowing easy interfacing when the
ISP1181 is the only device in that area. If in the example circuit for bus configuration
mode 0 (see
Figure 35
) the ISP1181 is mapped to address FFFF08H (in area 7),
output CS7 of the H8S/2357 can be directly connected to input CS of the ISP1181.
The external bus specifications, bus width, number of access states and number of
program wait states can be programmed for each address area. The recommended
settings of H8S/2357 for interfacing the ISP1181 are:
8-bit bus in Bus Width Control Register (ABWCR)
enable wait states in Access State Control Register (ASTCR)
1 program wait state in the Wait Control Register (WCRH and WCRL).
20.2.3
Using DMA
The ISP1181 can be configured for several methods of DMA with the H8S/2357 and
other devices. The interface circuit in
Figure 35
shows an example of the ISP1181
working with the H8S/2357 in single-address DACK-only DMA mode. External
devices are not shown.
For single-address DACK-only mode, firmware must program the following settings:
ISP1181
:
–
program the DMA Counter register with the total transfer byte count
–
program the Hardware Configuration Register to select active level LOW for
DREQ and DACK
–
select the target endpoint and transfer direction
–
select DACK-only mode and enable DMA transfer.
相關PDF資料
PDF描述
ISP1181DGG INDUCTOR 4.7NH +-.3NH 0402 SMD
ISP1183 Low-power Universal Serial Bus interface device with DMA
ISP1183BS Low-power Universal Serial Bus interface device with DMA
ISP1301 Universal Serial Bus On-The-Go transceiver
ISP1301BS Universal Serial Bus On-The-Go transceiver
相關代理商/技術參數
參數描述
ISP1181A 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus peripheral controller
ISP1181ABS 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus peripheral controller
ISP1181ABS,518 功能描述:USB 接口集成電路 USB 1.1 ADV DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1181ABS,551 功能描述:USB 接口集成電路 USB 1.1 ADVANCED DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1181ABS,557 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*