參數資料
型號: ISP1161
廠商: NXP Semiconductors N.V.
英文描述: Full-speed Universal Serial Bus single-chip host and device controller
中文描述: 全速通用串行總線的單芯片主機和設備控制器
文件頁數: 36/127頁
文件大?。?/td> 2762K
代理商: ISP1161
Philips Semiconductors
ISP1161
Full-speed USB single-chip host and device controller
Product data
Rev. 01 — 3 July 2001
36 of 130
9397 750 08313
Philips Electronics N.V. 2001. All rights reserved.
Control Transaction Limitations
The different phases of a Control transfer (SETUP, Data and Status) should never be
put in the same ATL.
9.6 Microprocessor loading
The maximum amount of data that can be transferred for an endpoint during one
frame is 1023 bytes. The number of USB packets that are needed for this batch of
data depends on the Maximum Packet Size that is specified.
The HC Driver has to schedule the transactions in a frame. On the other hand, the
microprocessor must have the ability to handle the interrupts coming from HC every
1 ms. It must also be able to do the scheduling for the next frame, reading the frame
information from and writing the next frame information to the buffer RAM in the time
between the end of the current frame and the start of the next frame.
9.7 Internal 15 k
pull-down resistors for downstream ports
There are four internal 15 k
pull-down resistors built in ISP1161 for the two
downstream ports: two resistors for each port. These resistors are software
selectable by programming bit 12 of the HcHardwareConfiguration register (20H -
Read, A0H - Write). When bit 12 is cleared to logic 0, it means that external 15 k
pull-down resistors should be used. Bit 12 is set to logic 1 that indicates the internal
built in 15 k
pull-down resistors will be used instead of external ones. See
Figure 33
.
This feature is a cost-saving option. However, the power on reset default value is
logic 0. If you want to use the internal resistors, the HC Driver must check this bit
status after every reset, because a reset action will clear this bit regardless of it being
a hardware reset or a software reset.
Fig 32. HC time domain behavior: example 3.
MGT956
(frame N)
(frame N
+
1)
(frame N
+
2)
(frame N
+
3)
相關PDF資料
PDF描述
ISP1161A1 Universal Serial Bus single-chip host and device controller
ISP1161A1BD Universal Serial Bus single-chip host and device controller
ISP1161A1BM Universal Serial Bus single-chip host and device controller
ISP1161BD Full-speed Universal Serial Bus single-chip host and device controller
ISP1161BM Full-speed Universal Serial Bus single-chip host and device controller
相關代理商/技術參數
參數描述
ISP1161A 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus single-chip host and device controller
ISP1161A1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus single-chip host and device controller
ISP1161A1BD 功能描述:IC USB HOST/DEVICE CTRLR 64-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN(6x6) 包裝:* 其它名稱:Q6396337A
ISP1161A1BD,118 功能描述:USB 接口集成電路 USB1.1 HOST &DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1161A1BD,151 功能描述:USB 接口集成電路 USB1.1 HOST &DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20