- 您現在的位置：買賣IC網 > PDF目錄383009 > GM5110-H (Electronic Theatre Controls, Inc.) XGA/SXGA LCD Controller PDF資料下載
參數資料
| 型號： | GM5110-H |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | XGA/SXGA LCD Controller |
| 中文描述： | 的XGA / SXGA LCD控制器 |
| 文件頁數： | 19/51頁 |
| 文件大?。?/td> | 1379K |
| 代理商： | GM5110-H |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
***
Genesis Microchip Confidential ***
gm5110/20 Preliminary Data Sheet
June 2002
12
C5110-DAT-01C
The TCLK oscillator uses a Pierce Oscillator circuit. The output of the oscillator circuit,
measured at the TCLK pin, is an approximate sine wave with a bias of about 2 volts above
ground (see Figure 5). The peak-to-peak voltage of the output can range from 250 mV to
1000 mV depending on the specific characteristics of the crystal and variation in the
oscillator characteristics. The output of the oscillator is connected to a comparator that
converts the sine wave to a square wave. The comparator requires a minimum signal level of
about 50-mV peak to peak to function correctly. The output of the comparator is buffered and
then distributed to the gm5110/20 circuits.
~ 2 Volts
3.3 Volts
250 mV peak to peak
to
1000 mV peak to peak
time
Figure 5.
Internal Oscillator Output
One of the design parameters that must be given some consideration is the value of the
loading capacitors used with the crystal as shown in Figure 6. The loading capacitance (C
load
)
on the crystal is the combination of C
L1
and C
L2
and is calculated by C
load
= ((C
L1
* C
L2
) /
(C
L1
+ C
L2
)) + C
shunt
. The shunt capacitance C
shunt
is the effective capacitance between the
XTAL and TCLK pins. For the gm5110/20 this is approximately 9 pF. C
L1
and C
L2
are a
parallel combination of the external loading capacitors (C
ex
), the PCB board capacitance
(C
pcb
), the pin capacitance (C
pin
), the pad capacitance (C
pad
), and the ESD protection
capacitance (C
esd
). The capacitances are symmetrical so that C
L1
= C
L2
= C
ex
+ C
PCB
+ C
pin
+
C
pad
+ C
ESD
. The correct value of C
ex
must be calculated based on the values of the load
capacitances. Approximate values are provided in Figure 6.
相關PDF資料 |
PDF描述 |
|---|---|
| GM5120 | XGA/SXGA LCD Controller |
| GM5120-H | XGA/SXGA LCD Controller |
| GM2126 | ANALOG INTERFACE ONPANEL SXGA LCD CONTROLLER WITH RSDS TRANSMITTER |
| GM5115 | ONPANEL LCD PANEL CONTROLLER |
| GM5115-H | ONPANEL LCD PANEL CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GM5115 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ONPANEL LCD PANEL CONTROLLER |
| GM5115-H | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ONPANEL LCD PANEL CONTROLLER |
| GM5120 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:XGA/SXGA LCD Controller |
| GM5120-H | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:XGA/SXGA LCD Controller |
| GM5125 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ONPANEL LCD PANEL CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。