參數資料
型號： EVAL-ADUC7028QSZ
廠商： Analog Devices Inc
文件頁數： 81/104頁
文件大?。?/td> 0K
描述： KIT DEV ADUC7028 QUICK START
產品培訓模塊： ARM7 Applications & Tools
Intro to ARM7 Core & Microconverters
Process Control
標準包裝： 1
系列： QuickStart™ 套件
類型： MCU
適用于相關產品： ADuC7028
所含物品： 評估板、電源、纜線、軟件和說明文檔
產品目錄頁面： 739 (CN2011-ZH PDF)
相關產品： ADUC7028BBCZ62-RL-ND - IC MCU FLASH 62K 12BIT
ADUC7028BBCZ62-ND - IC MCU FLASH 62K 12BIT
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 78 of 104
Table 137. I2CxALT Registers
Name
Address
Default Value
Access
I2C0ALT
0xFFFF0828
0x00
R/W
I2C1ALT
0xFFFF0928
0x00
R/W
I2CxALT are hardware general call ID registers used in slave mode.
Table 138. I2CxCFG Registers
Name
Address
Default Value
Access
I2C0CFG
0xFFFF082C
0x00
R/W
I2C1CFG
0xFFFF092C
0x00
R/W
I2CxCFG are configuration registers.
Table 139. I2C0CFG MMR Bit Descriptions
Bit
Description
31:5
Reserved. These bits should be written by the user as 0.
14
Enable stop interrupt. Set by the user to generate an interrupt upon receiving a stop condition and after receiving a valid start
condition and matching address. Cleared by the user to disable the generation of an interrupt upon receiving a stop condition.
13
Reserved.
12
Reserved.
11
Enable stretch SCL (holds SCL low). Set by the user to stretch the SCL line. Cleared by the user to disable stretching of the SCL line.
10
Reserved.
9
Slave Tx FIFO request interrupt enable. Set by the user to disable the slave Tx FIFO request interrupt. Cleared by the user to generate
an interrupt request just after the negative edge of the clock for the R/W bit. This allows the user to input data into the slave Tx FIFO if
it is empty. At 400 ksps and the core clock running at 41.78 MHz, the user has 45 clock cycles to take appropriate action, taking
interrupt latency into account.
8
General call status bit clear. Set by the user to clear the general call status bits. Cleared automatically by hardware after the general
call status bits are cleared.
7
Master serial clock enable bit. Set by user to enable generation of the serial clock in master mode. Cleared by user to disable serial
clock in master mode.
6
Loopback enable bit. Set by user to internally connect the transition to the reception to test user software. Cleared by user to operate
in normal mode.
5
Start backoff disable bit. Set by user in multimaster mode. If losing arbitration, the master immediately tries to retransmit. Cleared by
user to enable start backoff. After losing arbitration, the master waits before trying to retransmit.
4
Hardware general call enable. When this bit and Bit 3 are set and have received a general call (Address 0x00) and a data byte, the
device checks the contents of I2C0ALT against the receive register. If the contents match, the device has received a hardware general
call. This is used if a device needs urgent attention from a master device without knowing which master it needs to turn to. This is a
“to whom it may concern” call. The ADuC7019/20/21/22/24/25/26/27/28/29 watch for these addresses. The device that requires
attention embeds its own address into the message. All masters listen, and the one that can handle the device contacts its slave and
acts appropriately. The LSB of the I2C0ALT register should always be written to 1, as indicated in The I2C-Bus Specification, January
2000, from NXP.
3
General call enable bit. This bit is set by the user to enable the slave device to acknowledge (ACK) an I2C general call, Address 0x00
(write). The device then recognizes a data bit. If it receives a 0x06 (reset and write programmable part of slave address by hardware)
as the data byte, the I2C interface resets as as indicated in The I2C-Bus Specification, January 2000, from NXP. This command can be
used to reset an entire I2C system. The general call interrupt status bit sets on any general call. The user must take corrective action by
setting up the I2C interface after a reset. If it receives a 0x04 (write programmable part of slave address by hardware) as the data byte,
the general call interrupt status bit sets on any general call. The user must take corrective action by reprogramming the device address.
2
Reserved.
1
Master enable bit. Set by user to enable the master I2C channel. Cleared by user to disable the master I2C channel.
0
Slave enable bit. Set by user to enable the slave I2C channel. A slave transfer sequence is monitored for the device address in I2C0ID0,
I2C0ID1, I2C0ID2, and I2C0ID3. At 400 kSPs, the core clock should run at 41.78 MHz because the interrupt latency could be up to 45
clock cycles alone. After the I2C read bit, the user has 0.5 of an I2C clock cycle to load the Tx FIFO. AT 400 kSPS, this is 1.26 μs, the
interrupt latency.
相關PDF資料
PDF描述
GMM12DREN CONN EDGECARD 24POS .156 EYELET
GSM12DREH CONN EDGECARD 24POS .156 EYELET
EA-XPR-001 BOARD LPCXPRESSO LPC1343
EVAL-ADUC841QSZ KIT DEV FOR ADUC841 QUICK START
HBM11DRAI CONN EDGECARD 22POS R/A .156 SLD
相關代理商/技術參數
參數描述
EVAL-ADUC7029QSZ 功能描述:EVAL DEV SYSTEM FOR ADUC7029 RoHS:否 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:* 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF)
EVAL-ADUC7029QSZ 制造商:Analog Devices 功能描述:Silicon Manufacturer:Analog Devices C
EVAL-ADUC7032QSPZ 制造商:Analog Devices 功能描述:EVAL BD FOR ADUC7032 - Bulk
EVAL-ADUC7033QSPZ 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Bulk
EVAL-ADUC7034QSPZ 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*