參數資料
型號： EVAL-ADUC7028QSZ
廠商： Analog Devices Inc
文件頁數： 63/104頁
文件大?。?/td> 0K
描述： KIT DEV ADUC7028 QUICK START
產品培訓模塊： ARM7 Applications & Tools
Intro to ARM7 Core & Microconverters
Process Control
標準包裝： 1
系列： QuickStart™ 套件
類型： MCU
適用于相關產品： ADuC7028
所含物品： 評估板、電源、纜線、軟件和說明文檔
產品目錄頁面： 739 (CN2011-ZH PDF)
相關產品： ADUC7028BBCZ62-RL-ND - IC MCU FLASH 62K 12BIT
ADUC7028BBCZ62-ND - IC MCU FLASH 62K 12BIT
Data Sheet
ADuC7019/20/21/22/24/25/26/27/28/29
Rev. F | Page 61 of 104
DIGITAL PERIPHERALS
3-PHASE PWM
Each ADuC7019/20/21/22/24/25/26/27/28/29 provides a flexible
and programmable, 3-phase pulse-width modulation (PWM)
waveform generator. It can be programmed to generate the
required switching patterns to drive a 3-phase voltage source
inverter for ac induction motor control (ACIM). Note that only
active high patterns can be produced.
The PWM generator produces three pairs of PWM signals on
the six PWM output pins (PWM0H, PWM0L, PWM1H, PWM1L,
PWM2H, and PWM2L). The six PWM output signals consist of
three high-side drive signals and three low-side drive signals.
The switching frequency and dead time of the generated PWM
patterns are programmable using the PWMDAT0 and PWMDAT1
MMRs. In addition, three duty-cycle control registers (PWMCH0,
PWMCH1, and PWMCH2) directly control the duty cycles of
the three pairs of PWM signals.
Each of the six PWM output signals can be enabled or disabled
by separate output enable bits of the PWMEN register. In addition,
three control bits of the PWMEN register permit crossover of
the two signals of a PWM pair. In crossover mode, the PWM
signal destined for the high-side switch is diverted to the comple-
mentary low-side output. The signal destined for the low-side
switch is diverted to the corresponding high-side output signal.
In many applications, there is a need to provide an isolation
barrier in the gate-drive circuits that turn on the inverter power
devices. In general, there are two common isolation techniques:
optical isolation using optocouplers and transformer isolation
using pulse transformers. The PWM controller permits mixing
of the output PWM signals with a high frequency chopping signal
to permit easy interface to such pulse transformers. The features
of this gate-drive chopping mode can be controlled by the
PWMCFG register. An 8-bit value within the PWMCFG
register directly controls the chopping frequency. High
frequency chopping can be independently enabled for the high-
side and low-side outputs using separate control bits in the
PWMCFG register.
The PWM generator can operate in one of two distinct modes:
single update mode or double update mode. In single update
mode, the duty cycle values are programmable only once per
PWM period so that the resulting PWM patterns are symmetrical
about the midpoint of the PWM period. In the double update
mode, a second updating of the PWM duty cycle values is
implemented at the midpoint of the PWM period.
In double update mode, it is also possible to produce asymmetrical
PWM patterns that produce lower harmonic distortion in 3-phase
PWM inverters. This technique permits closed-loop controllers
to change the average voltage applied to the machine windings
at a faster rate. As a result, faster closed-loop bandwidths are
achieved. The operating mode of the PWM block is selected by
a control bit in the PWMCON register. In single update mode,
an internal synchronization pulse, PWMSYNC, is produced at
the start of each PWM period. In double update mode, an
additional PWMSYNC pulse is produced at the midpoint of
each PWM period.
The PWM block can also provide an internal synchronization
pulse on the PWMSYNC pin that is synchronized to the PWM
switching frequency. In single update mode, a pulse is produced
at the start of each PWM period. In double update mode, an
additional pulse is produced at the mid-point of each PWM period.
The width of the pulse is programmable through the PWMDAT2
register. The PWM block can also accept an external synchro-
nization pulse on the PWMSYNC pin. The selection of external
synchronization or internal synchronization is in the PWMCON
register. The SYNC input timing can be synchronized to the
internal peripheral clock, which is selected in the PWMCON
register. If the external synchronization pulse from the chip pin is
asynchronous to the internal peripheral clock (typical case), the
external PWMSYNC is considered asynchronous and should be
synchronized. The synchronization logic adds latency and jitter
from the external pulse to the actual PWM outputs. The size of
the pulse on the PWMSYNC pin must be greater than two core
clock periods.
The PWM signals produced by the ADuC7019/20/21/22/24/25/
26/27/28/29 can be shut off via a dedicated asynchronous PWM
shutdown pin, PWMTRIP. When brought low, PWMTRIP instanta-
neously places all six PWM outputs in the off state (high). This
hardware shutdown mechanism is asynchronous so that the
associated PWM disable circuitry does not go through any
clocked logic. This ensures correct PWM shutdown even in
the event of a core clock loss.
Status information about the PWM system is available to the user
in the PWMSTA register. In particular, the state of the PWMTRIP
pin is available, as well as a status bit that indicates whether oper-
ation is in the first half or the second half of the PWM period.
40-Pin Package Devices
On the 40-pin package devices, the PWM outputs are not
directly accessible, as described in the General-Purpose
Input/Output section. One channel can be brought out on a
GPIO (see Table 78) via the PLA as shown in the following
example:
PWMCON = 0x1;
// enables PWM o/p
PWMDAT0 = 0x055F;
// PWM switching freq
// Configure Port Pins
GP4CON = 0x300;
// P4.2 as PLA output
GP3CON = 0x1;
// P3.0 configured as
// output of PWM0
//(internally)
// PWM0 onto P4.2
PLAELM8 = 0x0035;
// P3.0 (PWM output)
// input of element 8
PLAELM10 = 0x0059;
// PWM from element 8
相關PDF資料
PDF描述
GMM12DREN CONN EDGECARD 24POS .156 EYELET
GSM12DREH CONN EDGECARD 24POS .156 EYELET
EA-XPR-001 BOARD LPCXPRESSO LPC1343
EVAL-ADUC841QSZ KIT DEV FOR ADUC841 QUICK START
HBM11DRAI CONN EDGECARD 22POS R/A .156 SLD
相關代理商/技術參數
參數描述
EVAL-ADUC7029QSZ 功能描述:EVAL DEV SYSTEM FOR ADUC7029 RoHS:否 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:* 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF)
EVAL-ADUC7029QSZ 制造商:Analog Devices 功能描述:Silicon Manufacturer:Analog Devices C
EVAL-ADUC7032QSPZ 制造商:Analog Devices 功能描述:EVAL BD FOR ADUC7032 - Bulk
EVAL-ADUC7033QSPZ 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Bulk
EVAL-ADUC7034QSPZ 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*