- 您現在的位置：買賣IC網 > PDF目錄17112 > EVAL-ADUC7028QSZ (Analog Devices Inc)KIT DEV ADUC7028 QUICK START PDF資料下載
參數資料
| 型號： | EVAL-ADUC7028QSZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 59/104頁 |
| 文件大小： | 0K |
| 描述： | KIT DEV ADUC7028 QUICK START |
| 產品培訓模塊： | ARM7 Applications & Tools Intro to ARM7 Core & Microconverters Process Control |
| 標準包裝： | 1 |
| 系列： | QuickStart™ 套件 |
| 類型： | MCU |
| 適用于相關產品： | ADuC7028 |
| 所含物品： | 評估板、電源、纜線、軟件和說明文檔 |
| 產品目錄頁面： | 739 (CN2011-ZH PDF) |
| 相關產品： | ADUC7028BBCZ62-RL-ND - IC MCU FLASH 62K 12BIT ADUC7028BBCZ62-ND - IC MCU FLASH 62K 12BIT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 58 of 104
Input offset voltage (VOS) is the difference between the center of
the hysteresis range and the ground level. This can either be
positive or negative. The hysteresis voltage (VH) is one-half the
width of the hysteresis range.
Comparator Interface
The comparator interface consists of a 16-bit MMR, CMPCON,
which is described in Table 56.
Table 55. CMPCON Register
Name
Address
Default Value
Access
CMPCON
0xFFFF0444
0x0000
R/W
Table 56. CMPCON MMR Bit Descriptions
Bit
Name
Value
Description
15:11
Reserved.
10
CMPEN
Comparator enable bit. Set by user
to enable the comparator. Cleared
by user to disable the comparator.
9:8
CMPIN
Comparator negative input
select bits.
00
AVDD/2.
01
ADC3 input.
10
DAC0 output.
11
Reserved.
7:6
CMPOC
Comparator output configuration
bits.
00
Reserved.
01
Reserved.
10
Output on CMPOUT.
11
IRQ.
5
CMPOL
Comparator output logic state bit.
When low, the comparator output
is high if the positive input (CMP0)
is above the negative input (CMP1).
When high, the comparator output
is high if the positive input is below
the negative input.
4:3
CMPRES
Response time.
00
5 s response time is typical for
large signals (2.5 V differential).
17 s response time is typical for
small signals (0.65 mV differential).
11
3 s typical.
01/10
Reserved.
2
CMPHYST
Comparator hysteresis bit. Set by
user to have a hysteresis of about
7.5 mV. Cleared by user to have no
hysteresis.
1
CMPORI
Comparator output rising edge
interrupt. Set automatically when a
rising edge occurs on the moni-
tored voltage (CMP0). Cleared by
user by writing a 1 to this bit.
0
CMPOFI
Comparator output falling edge
interrupt. Set automatically when a
falling edge occurs on the monitored
voltage (CMP0). Cleared by user.
OSCILLATOR AND PLL—POWER CONTROL
Clocking System
Each ADuC7019/20/21/22/24/25/26/27/28/29 integrates a
32.768 kHz ±3% oscillator, a clock divider, and a PLL. The PLL
locks onto a multiple (1275) of the internal oscillator or an external
32.768 kHz crystal to provide a stable 41.78 MHz clock (UCLK) for
the system. To allow power saving, the core can operate at this
frequency, or at binary submultiples of it. The actual core oper-
ating frequency, UCLK/2CD, is refered to as HCLK. The default
core clock is the PLL clock divided by 8 (CD = 3) or 5.22 MHz.
The core clock frequency can also come from an external clock
on the ECLK pin as described in Figure 67. The core clock can
be outputted on ECLK when using an internal oscillator or
external crystal.
Note that when the ECLK pin is used to output the core clock,
the output signal is not buffered and is not suitable for use as a
clock source to an external device without an external buffer.
04955-
026
*32.768kHz ±3%
AT POWER-UP
41.78MHz
OCLK
32.768kHz
WATCHDOG
TIMER
INT. 32kHz*
OSCILLATOR
CRYSTAL
OSCILLATOR
WAKE-UP
TIMER
MDCLK
HCLK
PLL
CORE
I2C
UCLK
ANALOG
PERIPHERALS
/2CD
CD
XCLKO
XCLKI
P0.7/XCLK
P0.7/ECLK
Figure 67. Clocking System
The selection of the clock source is in the PLLCON register. By
default, the part uses the internal oscillator feeding the PLL.
External Crystal Selection
To switch to an external crystal, the user must do the following:
1. Enable the Timer2 interrupt and configure it for a timeout
period of >120 s.
2. Follow the write sequence to the PLLCON register, setting
the MDCLK bits to 01 and clearing the OSEL bit.
3. Force the part into NAP mode by following the correct
write sequence to the POWCON register.
When the part is interrupted from NAP mode by the
Timer2 interrupt source, the clock source has switched to
the external clock.
相關PDF資料 |
PDF描述 |
|---|---|
| GMM12DREN | CONN EDGECARD 24POS .156 EYELET |
| GSM12DREH | CONN EDGECARD 24POS .156 EYELET |
| EA-XPR-001 | BOARD LPCXPRESSO LPC1343 |
| EVAL-ADUC841QSZ | KIT DEV FOR ADUC841 QUICK START |
| HBM11DRAI | CONN EDGECARD 22POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADUC7029QSZ | 功能描述:EVAL DEV SYSTEM FOR ADUC7029 RoHS:否 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:* 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF) |
| EVAL-ADUC7029QSZ | 制造商:Analog Devices 功能描述:Silicon Manufacturer:Analog Devices C |
| EVAL-ADUC7032QSPZ | 制造商:Analog Devices 功能描述:EVAL BD FOR ADUC7032 - Bulk |
| EVAL-ADUC7033QSPZ | 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Bulk |
| EVAL-ADUC7034QSPZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits) |
發布緊急采購，3分鐘左右您將得到回復。