- 您現在的位置：買賣IC網 > PDF目錄1915 > DS3120N (Maxim Integrated Products)IC FRAMER T1 28-CHANNEL IND PDF資料下載
參數資料
| 型號： | DS3120N |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 28/133頁 |
| 文件大小： | 0K |
| 描述： | IC FRAMER T1 28-CHANNEL IND |
| 標準包裝： | 1 |
| 控制器類型： | T1 調幀器 |
| 接口： | 并行/串行 |
| 電源電壓： | 2.97 V ~ 3.63 V |
| 電流 - 電源： | 300mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 316-BGA |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁
DS3112
123 of 133
14.3
T2 Framing Structure
To understand the M12 function users must understand T2 framing. The T2 frame structure is made up of
four subframes called M subframes (
). The four M subframes are transmitted one after
another (...M1/M2/M3/M4/M1/M2...) to make up the complete T2 M frame data structure. Each M
subframe is made up of six blocks and each block is made up of 49 bits. The first bit of each block is
dedicated to overhead and the next 48 bits are the information bits where the T1 data will be placed for
transport. The definitions of the overhead bits are shown in Table 14-2 and the placements of the
overhead bits are shown in Figure 14-3.
Table 14-2. T2 Overhead Bit Assignments
OVERHEAD BIT
DESCRIPTION
M Bits
(M1/M2/M3)
The M bits provide the frame alignment pattern for the four M subframes. Like all
framing patterns, the M bits are fixed to a certain state (M1 = 0/M2 = 1/M3 = 1).
F Bits
(F1/F2)
The F bits provide the frame alignment pattern for the M frame. Like all framing
patterns, the F bits are fixed to a certain state (F1 = 0/F2 = 1).
C Bits
(C1/C2/C3)
In the M12 application, the C bits are used to indicate when stuffing occurs. If all three
C Bits within a subframe are set to 1, then stuffing has occurred in the stuff block of
that subframe. If all three C Bits are set to zero, then no stuffing has occurred. When
the three C bits are not equal, a majority vote is used to determine the true state. The
exception to this rule is when the C3 bit is the inverse of C1 and C2. When this occurs,
it indicates that the T1 signal should be looped back.
X Bit
The X bit is used as a Remote Alarm Indication (RAI). It will be set to a zero (X = 0)
when the T2 framer cannot synchronize. It will be set to a one (X = 1) otherwise.
14.4 M12 Multiplexing
The M12 function multiplexes four T1 lines into a single T2 line. Since there are four M subframes in the
T2 framing structure, it might be concluded that each M subframe supports one T1 line but this is not the
case. The four T1 lines are bit interleaved into the T2 framing structure. A bit from T1 line #1 is placed
immediately after the overhead bit, followed by a bit from T1 line #2, which is followed by a bit from T1
line #3, which is followed by a bit from T1 line #4, and then the process repeats. Since there are 48
information bits in each block, there are 12 bits from each T1 line in a block. The second and fourth T1
lines are logically inverted before the bit interleaving occurs.
The four T1 lines are mapped asynchronously into the T2 data stream. This implies that there is no T1
framing information passed to the T2 level. The four T1 lines can have independent timing sources and
they do not need to be timing locked to the T2 clock. To account for differences in timing, bit stuffing is
used. The last block of each M subframe is the stuff block (
). In each stuff block there is an
associated stuff bit (Figure 14-4) that will be either an information bit (if the three C bits are decoded to
be a zero) or a stuff bit (if the three C bits are decoded to be a one). As shown in Figure 14-4 the position
of the stuff bit varies depending on the M subframe. This is done to allow a stuffing opportunity to occur
on each T1 line in every T2 M frame. For example, if the C bits in M Subframe 2 were all set to one, then
the second bit after the F2 overhead bit in the last block would be a stuff bit instead of an information bit.
相關PDF資料 |
PDF描述 |
|---|---|
| DS31256+ | IC CTRLR HDLC 256-CHANNEL 256BGA |
| DS3141+ | IC FRAMER DS3/E3 SNGL 144CSBGA |
| DS31412N | IC 12CH DS3/3 FRAMER 349-BGA |
| DS3150TN | IC LIU T3/E3/STS-1 IND 48-TQFP |
| DS3154N+ | IC LIU DS3/E3/STS-1 QD 144CSBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3121 | 功能描述:IC TGATOR T1-T3 AGGREGATOR RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| DS3121N | 功能描述:IC TGATOR T1-T3 AGGREGATOR IND RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| DS31256 | 功能描述:輸入/輸出控制器接口集成電路 256Ch High Thruput HDLC Cntlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| DS31256+ | 功能描述:輸入/輸出控制器接口集成電路 256Ch High Thruput HDLC Cntlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| DS31256B | 功能描述:輸入/輸出控制器接口集成電路 256Ch High Thruput HDLC Cntlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。