- 您現在的位置：買賣IC網 > PDF目錄16261 > DS3112DK (Maxim Integrated Products)KIT DEMO FOR DS3112 PDF資料下載
參數資料
| 型號： | DS3112DK |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 126/133頁 |
| 文件大小： | 0K |
| 描述： | KIT DEMO FOR DS3112 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 主要目的： | 接口，交叉點開關/多路復用器 |
| 已用 IC / 零件： | DS3112 |
| 已供物品： | 板，CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁當前第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁
DS3112
92 of 133
Bit 6: Receive Packet End (RPE). This latched read-only event-status bit will be set to a one each time the HDLC
controller detects the finish of a message whether the packet is valid (CRC correct) or not (bad CRC, abort
sequence detected, packet too small, not an integral number of octets, or an overrun occurred). This bit will be
cleared when read and will not be set again until another message end is detected. The setting of this bit can cause a
hardware interrupt to occur if the RPE bit in the Interrupt Mask for HSR (IHSR) register is set to a one and the
HDLC bit in the Interrupt Mask for MSR (IMSR) register is set to a one. The interrupt will be allowed to clear
when this bit is read.
Bit 4: Receive FIFO High Watermark (RHWM). This read-only real-time status bit will be set to a one when the
receive FIFO contains more than the number of bytes configured by the Receive High Watermark Setting control
bits (RHWMS0 to RHWMS2) in the HDLC Control Register (HCR). This bit will be cleared when the FIFO
empties below the high watermark. The setting of this bit can cause a hardware interrupt to occur if the RHWM bit
in the Interrupt Mask for HSR (IHSR) register is set to a one and the HDLC bit in the Interrupt Mask for MSR
(IMSR) register is set to a one.
Bit 5: Receive Packet Start (RPS). This latched read-only event-status bit will be set to a one each time the
HDLC controller detects an opening byte of an HDLC packet. This bit will be cleared when read and will not be set
again until another message is detected. The setting of this bit can cause a hardware interrupt to occur if the RPS bit
in the Interrupt Mask for HSR (IHSR) register is set to a one and the HDLC bit in the Interrupt Mask for MSR
(IMSR) register is set to a one. The interrupt will be allowed to clear when this bit is read.
Bit 7: Transmit FIFO Underrun (TUDR). This latched read-only event-status bit will be set to a one each time
the transmit FIFO underruns and an abort is automatically sent. This bit will be cleared when read and will not be
set again until another underrun occurs (i.e., the FIFO has been written to and then allowed to empty again). The
setting of this bit can cause a hardware interrupt to occur if the TUDR bit in the Interrupt Mask for HSR (IHSR)
register is set to a one and the HDLC bit in the Interrupt Mask for MSR (IMSR) register is set to a one. The
interrupt will be allowed to clear when this bit is read.
Bits 8 to 11: Transmit FIFO Level Bits 0 to 3 (TFL0 to TFL3). These read-only real-time status bits indicate the
current depth of the transmit FIFO with a 16-byte resolution. These status bits cannot cause a hardware interrupt.
TFL3
TFL2
TFL1
TFL0
TRANSMIT FIFO LEVEL
0
empty to 15 bytes
0
1
16 to 31 bytes
0
1
0
32 to 47 bytes
0
1
48 to 63 bytes
0
1
0
64 to 79 bytes
0
1
0
1
80 to 95 bytes
0
1
0
96 to 111 bytes
0
1
112 to 127 bytes
1
0
128 to 143 bytes
1
0
1
144 to 159 bytes
1
0
1
0
160 to 175 bytes
1
0
1
176 to 191 bytes
1
0
192 to 207 bytes
1
0
1
208 to 223 bytes
1
0
224 to 239 bytes
1
240 to 256 bytes
Bit 12: Transmit FIFO Empty (TEMPTY). This read-only real-time status bit will be set to a one when the
transmit FIFO is empty. It will be cleared when the transmit FIFO contains one or more bytes. This status bit
cannot cause a hardware interrupt.
Bit 13: Receive FIFO Overrun (ROVR). This latched read-only event-status bit will be set to a one each time the
receive FIFO overruns. This bit will be cleared when read and will not be set again until another overrun occurs
相關PDF資料 |
PDF描述 |
|---|---|
| RMM10DSEN | CONN EDGECARD 20POS .156 EYELET |
| DS2148DK | KIT DESIGN LIU DS2148 3/5V T1/E1 |
| H3CWH-6436G | IDC CABLE - HKC64H/AE64G/HPL64H |
| 78M6618-PDU-1 | EVAL KIT DS8005 |
| RMM10DSEH | CONN EDGECARD 20POS .156 EYELET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3112N | 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3112N+ | 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3112N+W | 功能描述:網絡控制器與處理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3112NC1 | 制造商:Maxim Integrated Products 功能描述:T3 E3 MULTIPLEXER, 3.3V T3/E3 FRAMER AND M13/E13/G.747 MUX - Rail/Tube |
| DS3112ND1E | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。