- 您現在的位置：買賣IC網 > PDF目錄15535 > DM164134 (Microchip Technology)KIT DEV PIC18F4XK22 PDF資料下載
參數資料
| 型號： | DM164134 |
| 廠商： | Microchip Technology |
| 文件頁數： | 70/116頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT DEV PIC18F4XK22 |
| 標準包裝： | 1 |
| 系列： | PIC® 18F |
| 類型： | MCU |
| 適用于相關產品： | PIC18F4XK22，PIC18F2XK22 |
| 所含物品： | 板，文檔 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁當前第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
2006 Microchip Technology Inc.
DS41159E-page 55
PIC18FXX8
4.12
Indirect Addressing, INDF and
FSR Registers
Indirect addressing is a mode of addressing data mem-
ory where the data memory address in the instruction
is not fixed. A SFR register is used as a pointer to the
data memory location that is to be read or written. Since
this pointer is in RAM, the contents can be modified by
the program. This can be useful for data tables in the
data memory and for software stacks. Figure 4-8
shows the operation of indirect addressing. This shows
the moving of the value to the data memory address
specified by the value of the FSR register.
Indirect addressing is possible by using one of the INDF
registers. Any instruction using the INDF register actually
accesses the register indicated by the File Select Regis-
ter, FSR. Reading the INDF register itself, indirectly
(FSR = 0), will read 00h. Writing to the INDF register
indirectly, results in a no operation. The FSR register
contains a 12-bit address which is shown in Figure 4-8.
The INDFn (0
≤ n ≤ 2) register is not a physical register.
Addressing INDFn actually addresses the register
whose address is contained in the FSRn register
(FSRn is a pointer). This is indirect addressing.
Example 4-5 shows a simple use of indirect addressing
to clear the RAM in Bank 1 (locations 100h-1FFh) in a
minimum number of instructions.
EXAMPLE 4-5:
HOW TO CLEAR RAM
(BANK 1) USING
INDIRECT ADDRESSING
There are three indirect addressing registers. To
address the entire data memory space (4096 bytes),
these registers are 12 bits wide. To store the 12 bits of
addressing
information,
two
8-bit
registers
are
required. These indirect addressing registers are:
1.
FSR0: composed of FSR0H:FSR0L
2.
FSR1: composed of FSR1H:FSR1L
3.
FSR2: composed of FSR2H:FSR2L
In addition, there are registers INDF0, INDF1 and
INDF2, which are not physically implemented. Reading
or writing to these registers activates indirect address-
ing, with the value in the corresponding FSR register
being the address of the data.
If an instruction writes a value to INDF0, the value will
be written to the address indicated by FSR0H:FSR0L.
A read from INDF1 reads the data from the address
indicated by FSR1H:FSR1L. INDFn can be used in
code anywhere an operand can be used.
If INDF0, INDF1 or INDF2 are read indirectly via an
FSR, all ‘0’s are read (zero bit is set). Similarly, if
INDF0, INDF1 or INDF2 are written to indirectly, the
operation will be equivalent to a NOP instruction and the
Status bits are not affected.
4.12.1
INDIRECT ADDRESSING
OPERATION
Each FSR register has an INDF register associated with
it, plus four additional register addresses. Performing an
operation on one of these five registers determines how
the FSR will be modified during indirect addressing.
When data access is done to one of the five
INDFn locations, the address selected will
configure the FSRn register to:
- Do nothing to FSRn after an indirect access
(no change) – INDFn
- Auto-decrement FSRn after an indirect
access (post-decrement) – POSTDECn
- Auto-increment FSRn after an indirect
access (post-increment) – POSTINCn
- Auto-increment FSRn before an indirect
access (pre-increment) – PREINCn
- Use the value in the WREG register as an
offset to FSRn. Do not modify the value of the
WREG or the FSRn register after an indirect
access (no change) – PLUSWn
When using the auto-increment or auto-decrement
features, the effect on the FSR is not reflected in the
Status register. For example, if the indirect address
causes the FSR to equal ‘0’, the Z bit will not be set.
Incrementing or decrementing an FSR affects all
12 bits. That is, when FSRnL overflows from an
increment, FSRnH will be incremented automatically.
Adding these features allows the FSRn to be used as a
software stack pointer in addition to its uses for table
operations in data memory.
Each FSR has an address associated with it that
performs an indexed indirect access. When a data
access to this INDFn location (PLUSWn) occurs, the
FSRn is configured to add the 2’s complement value in
the WREG register and the value in FSR to form the
address before an indirect access. The FSR value is not
changed.
If an FSR register contains a value that indicates one of
the INDFn, an indirect read will read 00h (zero bit is
set), while an indirect write will be equivalent to a NOP
(Status bits are not affected).
If an indirect addressing operation is done where the
target address is an FSRnH or FSRnL register, the
write operation will dominate over the pre- or
post-increment/decrement functions.
LFSR
FSR0, 100h ;
NEXT
CLRF
POSTINC0
; Clear INDF
; register
; & inc pointer
BTFSS
FSR0H, 1
; All done
; w/ Bank1?
BRA
NEXT
; NO, clear next
CONTINUE
;
:
; YES, continue
相關PDF資料 |
PDF描述 |
|---|---|
| AIUR-07-221K | INDUCTOR POWER 220UH 10% T/H |
| MAX8903CETI+ | IC DC/DC CHARGER LI+ 2A 28-TQFN |
| MAX11080GUU/V+T | IC LI/BATTERY MANAGEMENT 38TSSOP |
| MAX11081GUU+T | IC FAULT MON BATT 12CH 38-TSSOP |
| MAX11081GUU/V+T | IC FAULT MON BATT 12CH 38TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DM164135 | 制造商:Microchip Technology Inc 功能描述:KIT, ONEPIC DEMO BOARD, PLUS PICKIT 3 制造商:Microchip Technology Inc 功能描述:KIT, ONEPIC DEMO BOARD, PLUS PICKIT 3; SVHC:No SVHC (19-Dec-2012) ;RoHS Compliant: Yes 制造商:Microchip Technology Inc 功能描述:One PIC MCU Platform Board with PICkit 3 |
| DM164135 | 制造商:Microchip Technology Inc 功能描述:PICKIT 3 IN-CIRCUIT DEBUGGER |
| DM173001 | 功能描述:開發板和工具包 - PIC / DSPIC PICDEM 17 PIC17CXX RoHS:否 制造商:Microchip Technology 產品:Starter Kits 工具用于評估:chipKIT 核心:Uno32 接口類型: 工作電源電壓: |
| DM180021 | 功能描述:開發板和工具包 - PIC / DSPIC PIC18 Starter Kit RoHS:否 制造商:Microchip Technology 產品:Starter Kits 工具用于評估:chipKIT 核心:Uno32 接口類型: 工作電源電壓: |
| DM1800-434MB | 功能描述:射頻模塊 DM1800 Base Station 433.92 MHz RoHS:否 制造商:Linx Technologies 產品:Transceiver Modules 頻帶:902 MHz to 928 MHz 輸出功率:- 15.5 dBm to + 12.5 dBm 接口類型:UART 工作電源電壓:- 0.3 VDC to + 5.5 VDC 傳輸供電電流:38.1 mA 接收供電電流:22.7 mA 天線連接器類型:U.FL 最大工作溫度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
發布緊急采購，3分鐘左右您將得到回復。