- 您現在的位置：買賣IC網 > PDF目錄1900 > ADUC834BCPZ-REEL (Analog Devices Inc)IC MCU 62K FLASH ADC/DAC 56LFCSP PDF資料下載
參數資料
| 型號： | ADUC834BCPZ-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 42/80頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| 標準包裝： | 2,500 |
| 系列： | MicroConverter® ADuC8xx |
| 核心處理器： | 8052 |
| 芯體尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 連通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外圍設備： | POR，PSM，PWM，溫度傳感器，WDT |
| 輸入/輸出數： | 34 |
| 程序存儲器容量： | 62KB（62K x 8） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 5.25 V |
| 數據轉換器： | A/D 3x16b，4x24b; D/A 1x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 56-VFQFN 裸露焊盤，CSP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
REV. A
ADuC834
–47–
The main features of the MicroConverter I2C interface are:
Only two bus lines are required; a serial data line (SDATA)
and a serial clock line (SCLOCK).
An I
2C master can communicate with multiple slave devices.
Because each slave device has a unique 7-bit address then
single master/slave relationships can exist at all times even in
a multislave environment (Figure 35).
On-chip filtering rejects <50 ns spikes on the SDATA and
the SCLOCK lines to preserve data integrity.
DVDD
I2C
MASTER
I2C
SLAVE #1
I2C
SLAVE #2
Figure 35. Typical I2C System
Software Master Mode
The ADuC834 can be used as a I
2C master device by configuring
the I
2C peripheral in master mode and writing software to output
the data bit by bit, which is referred to as a software master. Master
mode is enabled by setting the I2CM bit in the I2CCON register.
To transmit data on the SDATA line, MDE must be set to enable
the output driver on the SDATA pin. If MDE is set then the
SDATA pin will be pulled high or low depending on whether the
MDO bit is set or cleared. MCO controls the SCLOCK pin and
is always configured as an output in Master mode. In Master
mode, the SCLOCK pin will be pulled high or low depending
on the whether MCO is set or cleared.
To receive data, MDE must be cleared to disable the output
driver on SDATA. Software must provide the clocks by toggling
the MCO bit and read SDATA pin via the MDI bit. If MDE is
cleared, MDI can be used to read the SDATA pin. The value of
the SDATA pin is latched into MDI on a rising edge of SCLOCK.
MDI is set if the SDATA pin was high on the last rising edge of
SCLOCK. MDI is clear if the SDATA pin was low on the last
rising edge of SCLOCK.
Software must control MDO, MCO, and MDE appropriately to
generate the START condition, slave address, acknowledge bits,
data bytes, and STOP conditions appropriately. These functions
are provided in Application Note uC001.
Hardware Slave Mode
After reset, the ADuC834 defaults to hardware slave mode. The
I
2C interface is enabled by clearing the SPE bit in SPICON.
Slave mode is enabled by clearing the I2CM bit in I2CCON.
The ADuC834 has a full hardware slave. In slave mode, the I
2C
address is stored in the I2CADD register. Data received or to be
transmitted is stored in the I2CDAT register.
Once enabled in I2C slave mode, the slave controller waits for a
START condition. If the ADuC834 detects a valid start condition,
followed by a valid address, and by the R/
W bit, the I2CI inter-
rupt bit will get automatically set by hardware.
The I2C peripheral will only generate a core interrupt if the user
has preconfigured the I2C interrupt enable bit in the IEIP2 SFR
as well as the global interrupt bit EA in the IE SFR, i.e.,
; Enabling I2C Interrupts for the ADuC834
MOV
IEIP2,#01h
; enable I2C interrupt
SETB EA
On the ADuC834 an auto clear of the I2CI bit is implemented
so this bit is cleared automatically on a read or write access to
the I2CDAT SFR.
MOV
I2CDAT, A
; I2CI auto-cleared MOV
A, I2CDAT
; I2CI auto-cleared
If for any reason the user tries to clear the interrupt more than
once, i.e., access the data SFR more than once per interrupt,
then the I2C controller will halt. The interface will then have to
be reset using the I2CRS bit.
The user can choose to poll the I2CI bit or enable the interrupt.
In the case of the interrupt, the PC counter will vector to 003BH
at the end of each complete byte. For the first byte when the
user gets to the I2CI ISR, the 7-bit address and the R/
W bit will
appear in the I2CDAT SFR.
The I2CTX bit contains the R/
W bit sent from the master. If
I2CTX is set then the master would like to receive a byte. Hence
the slave will transmit data by writing to the I2CDAT register.
If I2CTX is cleared, the master would like to transmit a byte.
Hence the slave will receive a serial byte. The software can
interrogate the state of I2CTX to determine whether it should
write to or read from I2CDAT.
Once the ADuC834 has received a valid address, hardware will
hold SCLOCK low until the I2CI bit is cleared by the software.
This allows the master to wait for the slave to be ready before
transmitting the clocks for the next byte.
The I2CI interrupt bit will be set every time a complete data
byte is received or transmitted provided it is followed by a valid
ACK. If the byte is followed by a NACK, an interrupt is NOT
generated. The ADuC834 will continue to issue interrupts for
each complete data byte transferred until a STOP condition is
received or the interface is reset.
When a STOP condition is received, the interface will reset to a
state where it is waiting to be addressed (idle). Similarly, if the
interface receives a NACK at the end of a sequence, it also
returns to the default idle state. The I2CRS bit can be used to
reset the I
2C interface. This bit can be used to force the inter-
face back to the default idle state.
It should be noted that there is no way (in hardware) to distin-
guish between an interrupt generated by a received START +
valid address and an interrupt generated by a received data byte.
User software must be used to distinguish between these interrupts.
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC836BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC843BSZ62-5 | IC ADC 12BIT W/FLASH MCU 52-MQFP |
| ADUC845BCPZ62-5 | IC FLASH MCU W/24BIT ADC 56-CSP |
| ADUC847BCPZ62-5 | IC MCU FLASH W/24BIT ADC 56-CSP |
| ADV202BBCZ-135 | IC CODEC VIDEO 135MHZ 144CSPBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC834BS | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 12.58MHZ 3.3/5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:8BIT MCU +24/16BIT ADC SMD MQFP52 |
| ADUC834BSZ | 功能描述:IC ADC DUAL16/24BIT W/MCU 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| ADUC836 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit-ADCs with Embedded 62 kB Flash MCU |
| ADUC836_02 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, Dual 16-Bit ADCs with Embedded 62 kB Flash MCU |
| ADUC836BCP | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。