參數資料
型號： ADUC7036CCPZ
廠商： Analog Devices Inc
文件頁數： 23/132頁
文件大?。?/td> 0K
描述： IC MCU 96K FLASH DUAL 48LFCSP
標準包裝： 1
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 20.48MHz
連通性： LIN，SPI，UART/USART
外圍設備： PSM，溫度傳感器，WDT
輸入/輸出數： 9
程序存儲器容量： 96KB（48K x 16）
程序存儲器類型： 閃存
RAM 容量： 1.5K x 32
電壓 - 電源 (Vcc/Vdd)： 3.5 V ~ 18 V
數據轉換器： A/D 2x16b
振蕩器型： 內部
工作溫度： -40°C ~ 115°C
封裝/外殼： 48-VFQFN 裸露焊盤，CSP
包裝： 托盤
ADuC7036
Rev. C | Page 119 of 132
Bit
Description
5
Enable compare interrupt bit.
Set to 1 by user code to generate an LHS interrupt (IRQEN[7]) when the value in LHSVAL0 (the LIN synchronization bit timer)
equals the value in the LHSCMP register. The LHS compare interrupt bit, LHSSTA[3], is set when this interrupt occurs. This
configuration is used in BSD write mode to allow user code to correctly time the output pulse widths of BSD bits to be transmitted.
Cleared to 0 by user code to disable compare interrupts.
4
Enable stop interrupt.
Set to 1 by user code to generate an interrupt when a stop condition occurs.
Cleared to 0 by user code to disable interrupts when a stop condition occurs.
3
Enable start interrupt.
Set to 1 by user code to generate an interrupt when a start condition occurs.
Cleared to 0 by user code to disable interrupts when a start condition occurs.
2
LIN sync enable bit.
Set to 1 by user code to enable LHS functionality.
Cleared to 0 by user code to disable LHS functionality.
1
Edge counter clear bit.
Set to 1 by user code to clear the internal edge counters in the LHS peripheral.
Cleared automatically to 0 after a 15 μs delay.
0
LHS reset bit.
Set to 1 by user code to reset all LHS logic to default conditions.
Cleared automatically to 0 after a 15 μs delay.
1 In BSD mode, LHSCON0[6] is set to 1. Because of the finite propagation delay in the BSD transmit (from the MCU to the external pin) and receive (from the external pin
to the MCU) paths, user code must not switch between BSD write and read modes until the MCU confirms that the external BSD pin is deasserted. Failure to adhere to
this recommendation may result in the generation of an inadvertent break condition interrupt after user code switches from BSD write mode to BSD read mode. A
stop condition interrupt can be used to ensure that this scenario is avoided.
LIN Hardware Synchronization Control Register 1
Name: LHSCON1
Address: 0xFFFF078C
Default Value: 0x00000032
Access: Read/write
Function: This 32-bit LHS control register, in conjunction with the LHSCON0 register, is used to configure the LIN mode of operation.
Table 94. LHSCON1 MMR Bit Designations
Bit
Description
31 to 8
Reserved. These bits are reserved for future use and should be written as 0 by user software.
7 to 4
LIN stop edge count. Set by user code to the number of falling or rising edges on which to stop the internal LIN
synchronization counter. The stop value of this counter can be read by user code using LHSVAL0. The type of edge, either
rising or falling, is configured by LHSCON0[7]. The default value of these bits is 0x3, which configures the hardware to
stop counting on the third falling edge. Note that the first falling edge is considered to be the falling edge at the start of
the LIN break pulse.
3 to 0
LIN start edge count. These four bits are set by user code to the number of falling edges that must occur before the
internal LIN synchronization timer starts counting. The stop value of this counter can be read by user code using
LHSVAL0. The default value of these bits is 0x2, which configures the hardware to start counting on the second falling
edge. Note that the first falling edge is considered to be the falling edge at the start of the LIN break pulse.
相關PDF資料
PDF描述
ADUC7039BCP6Z-RL IC MCU ARM7 BATT SENSER 32LFCSP
ADUC7061BCPZ32 IC MCU 16/32BIT 32KB 32LFCSP
ADUC7121BBCZ-RL PRECISION ANALOG MCU I.C
ADUC7122BBCZ-RL PRECISION ANALOG MCU I.C
ADUC7126BSTZ126-RL IC MCU 16/32B 126KB FLASH 80LQFP
相關代理商/技術參數
參數描述
ADUC7036CCPZ-RL 功能描述:IC MCU 96K FLASH DUAL 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7036DCPZ 功能描述:IC MCU 96K FLASH DUAL 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7036DCPZ-RL 功能描述:IC MCU 96K FLASH DUAL 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7038WBCPZ-RL 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Tape and Reel 制造商:Analog Devices 功能描述:IC MCU ARM7 制造商:Analog Devices 功能描述:ARM Microcontrollers - MCU Flash 64k ARM7 Dual 16-Bit ADC LIN IC 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C.
ADUC7039 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated, Precision Battery Sensor for Automotive Systems
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*