參數資料
型號: ADSP-21991BSTZ
廠商: Analog Devices Inc
文件頁數: 3/44頁
文件大?。?/td> 0K
描述: IC DSP CONTROLLER 16BIT 176-LQFP
產品變化通告: Product Discontinuance 27/Oct/2011
標準包裝: 1
系列: ADSP-21xx
類型: 定點
接口: SPI,SSP
時鐘速率: 160MHz
非易失內存: 外部
芯片上RAM: 112kB
電壓 - 輸入/輸出: 3.30V
電壓 - 核心: 2.50V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 176-LQFP
供應商設備封裝: 176-LQFP(24x24)
包裝: 托盤
–11–
REV. 0
ADSP-21991
There is no assigned priority for the peripheral interrupts after
reset. To assign the peripheral interrupts a different priority,
applications write the new priority to their corresponding control
bits (determined by their ID) in the Interrupt Priority Control
register.
Interrupt routines can either be nested with higher priority inter-
rupts taking precedence or processed sequentially. Interrupts can
be masked or unmasked with the IMASK register. Individual
interrupt requests are logically ANDed with the bits in IMASK;
the highest priority unmasked interrupt is then selected. The
emulation, power-down, and reset interrupts are nonmaskable
with the IMASK register, but software can use the DIS INT
instruction to mask the power-down interrupt.
The Interrupt Control (ICNTL) register controls interrupt
nesting and enables or disables interrupts globally.
The IRPTL register is used to force and clear interrupts. On-chip
stacks preserve the processor status and are automatically main-
tained during interrupt handling. To support interrupt, loop, and
subroutine nesting, the PC stack is 33 levels deep, the loop stack
is 8 levels deep, and the status stack is 16 levels deep. To prevent
stack overflow, the PC stack can generate a stack level interrupt
if the PC stack falls below 3 locations full or rises above 28
locations full.
The following instructions globally enable or disable interrupt
servicing, regardless of the state of IMASK.
ENA INT;
DIS INT;
At reset, interrupt servicing is disabled.
For quick servicing of interrupts, a secondary set of DAG and
computational registers exist. Switching between the primary
and secondary registers lets programs quickly service interrupts,
while preserving the state of the DSP.
Peripheral Interrupt Controller
The Peripheral Interrupt Controller is a dedicated peripheral unit
of the ADSP-21991 (accessed via IO mapped registers). The
peripheral interrupt controller manages the connection of up to
32 peripheral interrupt requests to the DSP core.
For each peripheral interrupt source, there is a unique 4-bit code
that allows the user to assign the particular peripheral interrupt
to any one of the 12 user assignable interrupts of the embedded
ADSP-219x core. Therefore, the peripheral interrupt controller
of the ADSP-21991 contains eight, 16-bit Interrupt Priority
Registers (Interrupt Priority Register 0 (IPR0) to Interrupt
Priority Register 7 (IPR7)).
Each Interrupt Priority Register contains a four 4-bit codes; one
specifically assigned to each peripheral interrupt. The user may
write a value between 0x0 and 0xB to each 4-bit location in order
to effectively connect the particular interrupt source to the cor-
responding user assignable interrupt of the ADSP-219x core.
Writing a value of 0x0 connects the peripheral interrupt to the
USR0 user assignable interrupt of the ADSP-219x core while
writing a value of 0xB connects the peripheral interrupt to the
USR11 user assignable interrupt. The core interrupt USR0 is the
highest priority user interrupt, while USR11 is the lowest priority.
Writing a value between 0xC and 0xF effectively disables the
peripheral interrupt by not connecting it to any ADSP-219x core
interrupt input. The user may assign more than one peripheral
interrupt to any given ADSP-219x core interrupt. In that case,
the onus is on the user software in the interrupt vector table to
determine the exact interrupt source through reading status bits.
This scheme permits the user to assign the number of specific
interrupts that are unique to their application to the interrupt
scheme of the ADSP-219x core. The user can then use the
existing interrupt priority control scheme to dynamically control
the priorities of the 12 core interrupts.
Low Power Operation
The ADSP-21991 has four low power options that significantly
reduce the power dissipation when the device operates under
standby conditions. To enter any of these modes, the DSP
executes an IDLE instruction. The ADSP-21991 uses the con-
figuration of the PD, STCK, and STALL bits in the PLLCTL
register to select between the low power modes as the DSP
executes the IDLE instruction. Depending on the mode, an
IDLE shuts off clocks to different parts of the DSP in the different
modes. The low power modes are:
Idle
Power-Down Core
Power-Down Core/Peripherals
Power-Down All
Idle Mode
When the ADSP-21991 is in Idle mode, the DSP core stops
executing instructions, retains the contents of the instruction
pipeline, and waits for an interrupt. The core clock and peripheral
clock continue running.
To enter Idle mode, the DSP can execute the IDLE instruction
anywhere in code. To exit Idle mode, the DSP responds to an
interrupt and (after two cycles of latency) resumes executing
instructions.
Power-Down Core Mode
When the ADSP-21991 is in Power-Down Core mode, the DSP
core clock is off, but the DSP retains the contents of the pipeline
and keeps the PLL running. The peripheral bus keeps running,
letting the peripherals receive data.
User Assigned Interrupt
(USR9)
13
0x00 01A0
User Assigned Interrupt
(USR10)
14
0x00 01C0
User Assigned Interrupt
(USR11)
—Lowest Priority
15
0x00 01E0
Table 2. Interrupt Priorities/Addresses
Interrupt
IMASK/
IRPTL
Vector Address
相關PDF資料
PDF描述
ADSP-21992YBC IC DSP CTLR 16BIT 196CSPBGA
ADSP-3PARCBF548M01 MODULE BOARD BF548
ADSP-BF506KSWZ-4F IC DSP 12BIT 400MHZ 120LQFP
ADSP-BF518BSWZ-4F4 IC DSP 16/32B 400MHZ LP 176LQFP
ADSP-BF526KBCZ-4C2 IC DSP CTRLR 400MHZ 289CSPBGA
相關代理商/技術參數
參數描述
ADSP-21992BBC 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 150MHz 150MIPS 196-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:MIXED SIGNAL DSP W/32K DM RAM& 16K PMRAM - Bulk
ADSP-21992BST 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 160MHz 160MIPS 176-Pin LQFP 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT
ADSP-21992BSTZ 功能描述:IC DSP CONTROLLER 16BIT 176LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP(數字式信號處理器) 系列:ADSP-21xx 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C,McASP,McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA,F(xiàn)CBGA 供應商設備封裝:548-FCBGA(27x27) 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
ADSP-21992YBC 功能描述:IC DSP CTLR 16BIT 196CSPBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP(數字式信號處理器) 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI,以太網,RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA,F(xiàn)CBGA 供應商設備封裝:431-FCPBGA(20x20) 包裝:托盤
ADSP-21992YST 制造商:Analog Devices 功能描述: