- 您現在的位置：買賣IC網 > PDF目錄10745 > AD73360LARZ-REEL7 (Analog Devices Inc)IC PROCESSOR FRONTEND 6CH 28SOIC PDF資料下載
參數資料
| 型號： | AD73360LARZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/35頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PROCESSOR FRONTEND 6CH 28SOIC |
| 標準包裝： | 400 |
| 位數： | 16 |
| 通道數： | 6 |
| 功率（瓦特）： | 80mW |
| 電壓 - 電源，模擬： | 3V |
| 電壓 - 電源，數字： | 3V |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC W |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
REV. A
AD73360
–18–
Control Register C
CRC:0
Global Power-Up. Writing a 1 to this bit will cause all six channels of the AD73360 to power-up regardless of the
status of the Power Control Bits in CRD-CRF. If less than six channels are required, this bit should be set to 0 and
the Power Control Bits of the relevant channels should be set to 1.
CRC:1–4
Reserved. These bits are reserved and should be programmed to 0 to ensure correct operation.
CRC:5
Power-Up Reference. This bit controls the state of the on-chip reference. A 1 in this bit will power up the refer-
ence. A 0 in this bit will power-down the reference. Note that the reference is automatically powered up if any
channel is enabled.
CRC:6
Reference Output. When this bit is set to 1, the REFOUT pin is enabled.
CRC:7
5 V Enable. When this bit is set to 1, the 5 V operating mode is enabled.
Control Register D
CRD:0–2
Input Gain Selection. These bits select the input gain for ADC1. See Table IV.
CRD:3
Power Control for ADC1. A 1 in this bit powers up ADC1.
CRD:4–6
Input Gain Selection. These bits select the input gain for ADC2. See Table IV.
CRD:7
Power Control for ADC2. A 1 in this bit powers up ADC2.
Control Register E
CRE:0-2
Input Gain Selection. These bits select the input gain for ADC3. See Table IV.
CRE:3
Power Control for ADC3. A 1 in this bit powers up ADC3.
CRE:4–6
Input Gain Selection. These bits select the input gain for ADC4. See Table IV.
CRE:7
Power Control for ADC4. A 1 in this bit powers up ADC4.
Control Register F
CRF:0–2
Input Gain Selection. These bits select the input gain for ADC5. See Table IV.
CRF:3
Power Control for ADC5. A 1 in this bit powers up ADC5.
CRF:4–6
Input Gain Selection. These bits select the input gain for ADC6. See Table IV.
CRF:7
Power Control for ADC6. A 1 in this bit powers up ADC6.
Control Register G
CRG:0–5
Channel Select. These bits are used in association with CRG:6 and CRG:7. If the Reset Analog Modulator bit
(CRG:6) is 1, then a 1 in a Channel Select bit location will reset the Analog Modulator for that channel. If the
Single-Ended Enable Mode bit (CRG:7) is 1, then a 1 in a Channel Select bit location will put that channel into
Single-Ended Mode. If any channel has its Channel Select bit set to 0, the channel will be set for Differentially-
Ended Mode and will not have its analog modulator reset regardless of the state of CRG:6 and CRG:7.
CRG:6
Reset Analog Modulator. Setting this bit to a 1 will reset the Analog Modulators for any channel whose Channel
Select bit (CRG:0–5) is set to 1. This bit should be set to 0 for normal operation.
CRG:7
Single-Ended Enable Mode. Setting this bit to a 1 will enable Single-Ended Mode on any channel whose Channel
Select bit (CRG:0–5) is set to 1. Setting this bit to 0 will select Differentially-Ended Input Mode for all channels.
Control Register H
CRH:0–5
Invert Select. These bits are used in association with CRH:7. If the Enable Invert Channel Mode bit (CRH:7) is 1,
then a 1 in a Channel Select bit location will put that channel into Inverted Mode. If any channel has its Channel
Select bit set to 0, the channel will not be inverted regardless of the state CRH:7.
CRH:6
Test Mode Enable. This bit should be set to 0 to ensure normal operation.
CRH:7
Enable Invert Channel Mode. Setting this bit to a 1 will enable invert any channel whose Channel Select bit
(CRH:0–5) is set to 1. Setting this bit to 0 will select Noninverted (Normal) Mode for all channels.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX965EUA+ | IC COMPARATOR R-R 8-UMAX |
| MAX966ESA+ | IC COMPARATOR R-R 8-SOIC |
| VE-JN4-MY-F1 | CONVERTER MOD DC/DC 48V 50W |
| MAX965ESA+ | IC COMPARATOR R-R 8-SOIC |
| VE-JN3-MY-F4 | CONVERTER MOD DC/DC 24V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7339 | 制造商:AD 制造商全稱:Analog Devices 功能描述:5 V Integrated High Speed ADC/Quad DAC System |
| AD7339BS | 制造商:Analog Devices 功能描述:Data Acquisition System Single ADC Quad DAC 8-Bit 52-Pin MQFP |
| AD7339BS-REEL | 制造商:Analog Devices 功能描述:Data Acquisition System Single ADC Quad DAC 8-Bit 52-Pin MQFP T/R |
| AD7339BSZ-REEL | 功能描述:IC ADC/QUAD DAC 5V W/REF 52-MQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - ADCs/DAC - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:數據采集系統（DAS） 分辨率（位）:16 b 采樣率（每秒）:21.94k 數據接口:MICROWIRE?，QSPI?，串行，SPI? 電壓電源:模擬和數字 電源電壓:1.8 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（6x6） 包裝:托盤 |
| AD734 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10 MHz, 4-Quadrant Multiplier/Divider |
發布緊急采購，3分鐘左右您將得到回復。