REV. 1.2.2 UNIVERSAL (3.3V AND 5V) PCI BUS QUAD UART 43 LCR[6]: Transmit Break Enable When enabled the Break control bit causes a b" />
參數資料
型號： XR17D154CV-0A-EVB
廠商： Exar Corporation
文件頁數： 38/69頁
文件大小： 0K
描述： EVAL BOARD FOR XR17D154 144TQFP
標準包裝： 1
系列： *
xr
XR17D154
REV. 1.2.2
UNIVERSAL (3.3V AND 5V) PCI BUS QUAD UART
43
LCR[6]: Transmit Break Enable
When enabled the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space", LOW state). This condition remains until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition (default).
Logic 1 = Forces the transmitter output (TX) to a “space”, LOW, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
5.8.8
Modem Control Register (MCR) - Read/Write
The MCR register is used for controlling the modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Pins
The DTR# pin may be used for automatic hardware flow control enabled by EFR bit-6 and MCR bit-2=1. If the
modem interface is not used, this output may be used for general purpose.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
MCR[1]: RTS# Pins
The RTS# pin may be used for automatic hardware flow control by enabled by EFR bit-6 and MCR bit-2=0. If
the modem interface is not used, this output may be used for general purpose.
Logic 0 = Force RTS# output HIGH (default).
Logic 1 = Force RTS# output LOW.
MCR[2]: DTR# or RTS# for Auto Flow Control
DTR# or RTS# auto hardware flow control select. This bit is in effect only when auto RTS/DTR is enabled by
EFR bit-6. DTR# selection is associated with DSR# and RTS# is with CTS#.
Logic 0 = Uses RTS# and CTS# pins for auto hardware flow control.
Logic 1 = Uses DTR# and DSR# pins for auto hardware flow control.
MCR[3]: (OP2)
The OP2 output is not available in the XR17D154. It is present for 16C550 compatibility during internal
loopback. See Figure 18. Logic 0 is default.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable internal loopback mode (default).
Logic 1 = Enable internal loopback mode, see loopback section and Figure 18.
TABLE 16: PARITY SELECTION
LCR BIT-5 LCR BIT-4 LCR BIT-3
PARITY SELECTION
X
0
No parity
0
1
Odd parity
0
1
Even parity
1
0
1
Force parity to mark, “1”
1
Forced parity to space, “0”
相關PDF資料
PDF描述
ECM22DCST CONN EDGECARD 44POS DIP .156 SLD
5349565-9 FOMM50 LEAD 2.5 TZ SC/PC-SC/PC
CM322522-R22ML INDUCTOR 220NH 360MA SMD
2-6374659-0 C/A LC TO LC MM 2.0MM 20M1
CDRH125/LDNP-330MC POWER INDUCTOR 33UH 2.6A SMD
相關代理商/技術參數
參數描述
XR17D154CV-F 功能描述:UART 接口集成電路 3.3V-5V 64B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17D154CVTR-F 制造商:Exar Corporation 功能描述:UART 4-CH 64Byte FIFO 3.3V/5V 144-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR17D154CVTR-F
XR17D154IV 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17D154IV-F 功能描述:UART 接口集成電路 3.3V-5V 64B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR17D154IVTR-F 制造商:Exar Corporation 功能描述:UART 4-CH 64Byte FIFO 3.3V/5V 144-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR17D154IVTR-F
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*