- 您現在的位置：買賣IC網 > PDF目錄371304 > X9530-B15I (Intersil Corporation) Temperature Compensated Laser Diode Controller PDF資料下載
參數資料
| 型號： | X9530-B15I |
| 廠商： | Intersil Corporation |
| 英文描述： | Temperature Compensated Laser Diode Controller |
| 中文描述： | 溫度補償激光二極管控制器 |
| 文件頁數： | 3/30頁 |
| 文件大?。?/td> | 479K |
| 代理商： | X9530-B15I |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
X9530
Characteristics subject to change without notice.
3 of 30
REV 3.7 8/26/04
www.xicor.com
The EEPROM array is internally organized as 272 x 8
bits with 16-Byte pages, and utilizes Xicor’s proprietary
Direct Write
TM
cells, providing a minimum endurance
of 100,000 Page Write cycles and a minimum data
retention of 100 years.
PIN ASSIGNMENTS
TSSOP
Pin
1
CSP
Pin
A3
Pin
Name
A0
Pin Description
Device Address Select Pin 0.
This pin determines the LSB of the device address
required to communicate using the 2-wire interface. The A0 pin has an on-chip pull-
down resistor.
Device Address Select Pin 1.
This pin determines the intermediate bit of the device
address required to communicate using the 2-wire interface. The A1 pin has an on-
chip pull-down resistor.
Device Address Select Pin 2.
This pin determines the MSB of the device address
required to communicate using the 2-wire interface. The A2 pin has an on-chip pull-
down resistor.
Supply Voltage.
Write Protect Control Pin.
This pin is a CMOS compatible input. When LOW, Write
Protection is enabled preventing any “Write” operation. When HIGH, various areas of
the memory can be protected using the Block Lock bits BL1 and BL0. The WP pin has
an on-chip pull-down resistor, which enables the Write Protection when this pin is left
floating.
Serial Clock.
This is a TTL compatible input pin. This input is the 2-wire interface clock
controlling data input and output at the SDA pin.
Serial Data.
This pin is the 2-wire interface data into or out of the device. It is TTL
compatible when used as an input, and it is Open Drain when used as an output. This
pin requires an external pull up resistor.
Current Generator 1 Output.
This pin sinks or sources current. The magnitude and
direction of the current is fully programmable and adaptive. The resolution is 8 bits.
Current Programming Resistor 1.
A resistor between this pin and Vss can set the
maximum output current available at pin I1. If no resistor is used, the maximum current
must be selected using control register bits.
Current Programming Resistor 2.
A resistor between this pin and Vss can set the
maximum output current available at pin I2. If no resistor is used, the maximum current
must be selected using control register bits.
Ground.
Sensor Voltage Input.
This voltage input may be used to drive the input of the on-
chip A/D converter.
Reference Voltage Input or Output.
This pin can be configured as either an Input or
an Output. As an Input, the voltage at this pin is provided by an external source. As
an Output, the voltage at this pin is a buffered output voltage of the on-chip bandgap
reference circuit. In both cases, the voltage at this pin is the reference for the A/D
converter and the two D/A converters.
Current Generator 2 Output.
This pin sinks or sources current. The magnitude and
direction of the current is fully programmable and adaptive. The resolution is 8 bits.
2
B2
A1
3
C2
A2
4
5
B3
E3
Vcc
WP
6
C3
SCL
7
D3
SDA
8
E2
I1
9
E1
R1
10
D1
R2
11
12
C1, D2
B1
Vss
VSense
13
A1
VRef
14
A2
I2
相關PDF資料 |
PDF描述 |
|---|---|
| X9530B15I | Temperature Compensated Laser Diode Controller |
| X9530-V14I | ; Sensor Input Type:Fiber-Optic; Sensing Range Max:3m; Sensor Output:PNP; Leaded Process Compatible:No; Mounting Type:DIN Rail; Peak Reflow Compatible (260 C):No; Sensor Housing:Rectangular |
| X9530B15I-T2 | SINGLEMODE FIBER PATCH CABLE, PLENUM ST-LC 5M |
| X98027 | PRELIMINARY INFORMATION |
| X98027L128-3.3-Z | 275MHz Triple Video Digitizer with Digital PLL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9530B15I-T1 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Temperature Compensated Laser Diode Controller |
| X9530B15I-T2 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Temperature Compensated Laser Diode Controller |
| X9530V14I | 功能描述:IC LASR CTRLR 1CHAN 5.5V 14TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9530-V14I | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Temperature Compensated Laser Diode Controller |
| X9530V14IT1 | 功能描述:IC LASER DIODE CTRLR 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
發布緊急采購，3分鐘左右您將得到回復。