參數資料
型號： W981216DH-75
廠商： WINBOND ELECTRONICS CORP
元件分類： DRAM
英文描述： 8M X 16 SYNCHRONOUS DRAM, 5.4 ns, PDSO54
封裝： 0.400 INCH, 0.80 MM PITCH, TSOP2-54
文件頁數： 5/44頁
文件大?。?/td> 1221K
代理商： W981216DH-75
W981216DH/ W9812G6DH
Publication Release Date: June 6, 2005
- 13 -
Revision A08
Notes:
(1) v = valid
x = Don’t care
L = Low Level H = High Level
(2) CKEn signal is input level when commands are provided.
CKEn-1 signal is the input level one clock cycle before the command is issued.
(3) These are state of bank designated by BS0, BS1 signals.
(4) Device state is full page burst operation.
(5) Power Down Mode can not be entered in the burst cycle.
When this command asserts in the burst cycle, device state is clock suspend mode.
12. FUNCTIONAL DESCRIPTION
12.1 Power Up and Initialization
The default power up state of the mode register is unspecified. The following power up and
initialization sequence need to be followed to guarantee the device being preconditioned to each user
specific needs.
During power up, all Vcc and VccQ pins must be ramp up simultaneously to the specified voltage
when the input signals are held in the “NOP” state. The power up voltage must not exceed VCC +0.3V
on any of the input pins or Vcc supplies. After power up, an initial pause of 200
S is required followed
by a precharge of all banks using the precharge command. To prevent data contention on the DQ bus
during power up, it is required that the DQM and CKE pins be held high during the initial pause period.
Once all banks have been precharged, the Mode Register Set Command must be issued to initialize
the Mode Register. An additional eight Auto Refresh cycles (CBR) are also required before or after
programming the Mode Register to ensure proper subsequent operation.
12.2 Programming Mode Register
After initial power up, the Mode Register Set Command must be issued for proper device operation.
All banks must be in a precharged state and CKE must be high at least one cycle before the Mode
Register Set Command can be issued. The Mode Register Set Command is activated by the low
signals of RAS, CAS, CS and WE at the positive edge of the clock. The address input data during this
cycle defines the parameters to be set as shown in the Mode Register Operation table. A new
command may be issued following the mode register set command once a delay equal to tRSC has
elapsed. Please refer to the next page for Mode Register Set Cycle and Operation Table.
12.3 Bank Activate Command
The Bank Activate command must be applied before any Read or Write operation can be executed.
The operation is similar to RAS activate in EDO DRAM. The delay from when the Bank Activate
command is applied to when the first read or write operation can begin must not be less than the RAS
to CAS delay time (tRCD). Once a bank has been activated it must be precharged before another Bank
Activate command can be issued to the same bank. The minimum time interval between successive
Bank Activate commands to the same bank is determined by the RAS cycle time of the device (tRC).
The minimum time interval between interleaved Bank Activate commands (Bank A to Bank B and vice
versa) is the Bank to Bank delay time (tRRD). The maximum time that each bank can be held active is
specified as tRAS (max).
相關PDF資料
PDF描述
W972GG8JB-25 256M X 8 DDR DRAM, 0.4 ns, PBGA60
WF512K32-150CJC 512K X 32 FLASH 5V PROM MODULE, 150 ns, CQCC68
W73B586A-09L 32K X 18 CACHE SRAM, 9 ns, PQCC52
WS512K32-100G4TM 2M X 8 MULTI DEVICE SRAM MODULE, 100 ns, CQFP68
WS512K32-35G4M 2M X 8 MULTI DEVICE SRAM MODULE, 35 ns, CQFP68
相關代理商/技術參數
參數描述
W9812G2GB 制造商:WINBOND 制造商全稱:Winbond 功能描述:1M 】 4 BANKS 】 32BITS SDRAM
W9812G2GB-6 制造商:WINBOND 制造商全稱:Winbond 功能描述:1M 】 4 BANKS 】 32BITS SDRAM
W9812G2GB-6I 制造商:WINBOND 制造商全稱:Winbond 功能描述:1M 】 4 BANKS 】 32BITS SDRAM
W9812G2GB-75 制造商:WINBOND 制造商全稱:Winbond 功能描述:1M 】 4 BANKS 】 32BITS SDRAM
W9812G2GH 制造商:WINBOND 制造商全稱:Winbond 功能描述:a high-speed synchronous dynamic random access memory (SDRAM), organized as 1,048,576 words 】 4 banks 】 32 bits
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*