- 您現在的位置：買賣IC網 > PDF目錄199412 > TMP86CH09NG 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PDIP32 PDF資料下載
參數資料
| 型號： | TMP86CH09NG |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PDIP32 |
| 封裝： | 0.400 INCH, 1.78 MM PITCH, LEAD FREE, PLASTIC, SDIP-32 |
| 文件頁數： | 64/120頁 |
| 文件大小： | 1743K |
| 代理商： | TMP86CH09NG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁當前第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
Page 37
TMP86FH09ANG
3.3 Interrupt Source Selector (INTSEL)
Each interrupt source that shares the interrupt source level with another interrupt source is allowed to enable the
interrupt latch only when it is selected in the INTSEL register. The interrupt controller does not hold interrupt
requests corresponding to interrupt sources that are not selected in the INTSEL register. Therefore, the INTSEL reg-
ister must be set appropriately before interrupt requests are generated.
The following interrupt sources share their interrupt source level; the source is selected onnthe register INTSEL.
1. INTTC4 and INT3 share the interrupt source level whose priority is 12.
Note: Always set "0" to bit 5 of INTSEL register.
3.4 Interrupt Sequence
An interrupt request, which raised interrupt latch, is held, until interrupt is accepted or interrupt latch is cleared to
“0” by resetting or an instruction. Interrupt acceptance sequence requires 8 machine cycles (2
s @16 MHz) after the
completion of the current instruction. The interrupt service task terminates upon execution of an interrupt return
instruction [RETI] (for maskable interrupts) or [RETN] (for non-maskable interrupts). Figure 3-1 shows the timing
chart of interrupt acceptance processing.
3.4.1 Interrupt acceptance processing is packaged as follows.
a. The interrupt master enable flag (IMF) is cleared to “0” in order to disable the acceptance of any fol-
lowing interrupt.
b. The interrupt latch (IL) for the interrupt source accepted is cleared to “0”.
c. The contents of the program counter (PC) and the program status word, including the interrupt master
enable flag (IMF), are saved (Pushed) on the stack in sequence of PSW + IMF, PCH, PCL. Mean-
while, the stack pointer (SP) is decremented by 3.
d. The entry address (Interrupt vector) of the corresponding interrupt service program, loaded on the vec-
tor table, is transferred to the program counter.
e. The instruction stored at the entry address of the interrupt service program is executed.
Note:When the contents of PSW are saved on the stack, the contents of IMF are also saved.
Interrupt source selector
INTSEL
(003EH)
76543
210
-
IL11ER
-
(Initial value: ***0 ****)
IL11ER
Selects INTTC4 or INT3
0: INTTC4
1: INT3
R/W
相關PDF資料 |
PDF描述 |
|---|---|
| TMP86CM29BU | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP64 |
| TMP86FH09NG | 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDIP32 |
| TMP86FS49BUG | 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64 |
| TMP86PS25F | 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| TMP87C800N | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMP86CH12MG | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:8 Bit Microcontroller |
| TMP86CH21AUG | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:8 Bit Microcontroller |
| TMP86CH21F | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:CMOS 8-Bit Microcontroller |
| TMP86CH21U | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:CMOS 8-Bit Microcontroller |
| TMP86CH22UG | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:8 Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。