參數資料
型號: TMP86CH09NG
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PDIP32
封裝: 0.400 INCH, 1.78 MM PITCH, LEAD FREE, PLASTIC, SDIP-32
文件頁數: 107/120頁
文件大?。?/td> 1743K
代理商: TMP86CH09NG
Page 76
8. 16-Bit TimerCounter 1 (TC1)
8.3 Function
TMP86FH09ANG
8.3.5 Pulse Width Measurement Mode
In the pulse width measurement mode, the up-counter starts counting by the input pulse triggering of the
TC1 pin, and counts up at the edge of the internal clock. Either the rising or falling edge of the internal clock is
selected as the trigger edge in TC1CR<TC1S>. Either the single- or double-edge capture is selected as the trig-
ger edge in TC1CR<MCAP1>.
When TC1CR<MCAP1> is set to “1” (single-edge capture)
Either high- or low-level input pulse width can be measured. To measure the high-level input pulse
width, set the rising edge to TC1CR<TC1S>. To measure the low-level input pulse width, set the
falling edge to TC1CR<TC1S>.
When detecting the edge opposite to the trigger edge used to start counting after the timer starts,
the up-counter captures the up-counter value into TC1DRB and generates an INTTC1 interrupt
request. The up-counter is cleared at this time, and then restarts counting when detecting the trigger
edge used to start counting.
When TC1CR<MCAP1> is set to “0” (double-edge capture)
The cycle starting with either the high- or low-going input pulse can be measured. To measure the
cycle starting with the high-going pulse, set the rising edge to TC1CR<TC1S>. To measure the cycle
starting with the low-going pulse, set the falling edge to TC1CR<TC1S>.
When detecting the edge opposite to the trigger edge used to start counting after the timer starts,
the up-counter captures the up-counter value into TC1DRB and generates an INTTC1 interrupt
request. The up-counter continues counting up, and captures the up-counter value into TC1DRB and
generates an INTTC1 interrupt request when detecting the trigger edge used to start counting. The
up-counter is cleared at this time, and then continues counting.
Note 1: The captured value must be read from TC1DRB until the next trigger edge is detected. If not read, the cap-
tured value becomes a don’t care. It is recommended to use a 16-bit access instruction to read the captured
value from TC1DRB.
Note 2: For the single-edge capture, the counter after capturing the value stops at “1” until detecting the next edge.
Therefore, the second captured value is “1” larger than the captured value immediately after counting
starts.
Note 3: The first captured value after the timer starts may be read incorrectively, therefore, ignore the first captured
value.
相關PDF資料
PDF描述
TMP86CM29BU 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP64
TMP86FH09NG 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDIP32
TMP86FS49BUG 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64
TMP86PS25F 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP100
TMP87C800N 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64
相關代理商/技術參數
參數描述
TMP86CH12MG 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:8 Bit Microcontroller
TMP86CH21AUG 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:8 Bit Microcontroller
TMP86CH21F 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:CMOS 8-Bit Microcontroller
TMP86CH21U 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:CMOS 8-Bit Microcontroller
TMP86CH22UG 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:8 Bit Microcontroller