參數資料
型號： ST623X-EMU2
廠商： 意法半導體
英文描述： REAL TIME EMULATION DEVELOPMENT TOOLS FOR ST6 MCU FAMILY
中文描述： 實時仿真開發工具，ST6單片機系列
文件頁數： 14/86頁
文件大小： 531K
代理商： ST623X-EMU2
14/86
ST62T30B ST62E30B
MEMORY MAP
(Cont’d)
Additional Notes on Parallel Mode:
If the user wishes to perform parallel program-
ming, the first step should be to set the E2PAR2
bit. From this time on, the EEPROM will be ad-
dressed in write mode, the ROW address will be
latched and it will be possible to change it only at
the end of the programming cycle, or by resetting
E2PAR2 without programming the EEPROM. Af-
ter the ROW addressis latched, the MCU can only
“see” the selected EEPROM row and any attempt
to write or read other rows will produce errors.
The EEPROM should not be read while E2PAR2
is set.
As soon as the E2PAR2 bit is set, the 8 volatile
ROW latches are cleared. From this moment on,
the user can load data in allor in part ofthe ROW.
Setting E2PAR1 will modify the EEPROM regis-
ters corresponding to the ROW latches accessed
after E2PAR2. For example, if the software sets
E2PAR2 and accesses the EEPROM by writing to
addresses 18h, 1Ah and 1Bh, and then sets
E2PAR1, these three registers will be modified si-
multaneously; the remaining bytes in the row will
be unaffected.
Note that E2PAR2 is internally reset at the end of
the programming cycle. This implies that the user
must setthe E2PAR2bit betweentwo parallel pro-
gramming cycles. Note that if the user tries to set
E2PAR1 while E2PAR2 is not set, there will be no
programming cycle and the E2PAR1 bit will be un-
affected. Consequently, the E2PAR1bit cannot be
set if E2ENA is low. The E2PAR1 bit can be setby
the user, only if the E2ENA and E2PAR2 bits are
also set.
EEPROM Control Register (EECTL)
Address: DFh
—
Reset status: 00h
Read/Write
Bit 7 =
D7
: Unused.
Bit 6=
E2OFF
:Stand-by EnableBit.WRITE ONLY.
If thisbitis settheEEPROM isdisabled(anyaccess
will bemeaningless) andthepower consumptionof
the EEPROM is reduced to its lowest value.
Bit 5-4 =
D5-D4
: Reserved.MUST be kept reset.
Bit 3 =
E2PAR1
: Parallel Start Bit. WRITE ONLY.
Once inParallelMode,assoonastheuser software
sets the E2PAR1 bit, parallel writing of the 8 adja-
cent registers will start. Thisbit is internally resetat
the end of the programming procedure. Note that
less than8 bytes can bewritten if required, the un-
defined bytes being unaffected by the parallel pro-
grammingcycle;thisisexplainedingreater detail in
the Additional Notes on Parallel Mode overleaf.
Bit 2 =
E2PAR2
: Parallel Mode En. Bit. WRITE
ONLY. This bit must be set by the user program in
order to perform parallel programming. If E2PAR2
is set and the parallel start bit (E2PAR1) is reset,
up to 8 adjacent bytes can be written simultane-
ously. These 8 adjacent bytes are considered as a
row, whose address lines A7, A6, A5, A4, A3 are
fixed while A2, A1 and A0 are the changing bits, as
illustrated in Table 6. E2PAR2 is automatically re-
set at the end of any parallel programming proce-
dure. It can be reset by the user software before
starting the programming procedure, thus leaving
the EEPROM registers unchanged.
Bit 1 =
E2BUSY
: EEPROM Busy Bit. READ ON-
LY. This bit is automatically set by the EEPROM
control logic when the EEPROM is in program-
ming mode. The userprogram should test it before
any EEPROM read or write operation; any attempt
to access the EEPROM while the busy bit is set
will be aborted and the writing procedure in
progress will be completed.
Bit 0 =
E2ENA
: EEPROM Enable Bit.WRITE ON-
LY. This bit enables programming of the EEPROM
cells. It must be set before any write to the EEP-
ROM register. Any attempt to write to the EEP-
ROM when E2ENA is low is meaningless and will
not trigger a write cycle.
7
0
D7 E2OFF
D5
D4
E2PAR1 E2PAR2 E2BUSY E2ENA
相關PDF資料
PDF描述
ST62T65BB3 8-BIT MICROCONTROLLER
ST62T65BB6 8-BIT MICROCONTROLLER
ST62T65BM3 8-BIT MICROCONTROLLER
ST62T65BM6 8-BIT MICROCONTROLLER
ST62E65BF1 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
ST623X-KIT 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STARTER KIT DATASHEET FOR ST6230
ST623X-KIT/110 功能描述:開發板和工具包 - 其他處理器 ST623X Starter Kit RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓:
ST623X-KIT/220 制造商:STMicroelectronics 功能描述:ST Development Kit, Including ST623X Starter Kit, Development Software CD-ROM, Parallel Cable, Power Supply, Window Development Devices ST62E30BF1, ST (More...)
ST623X-KIT/UK 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:STARTER KIT AB 8K BYTE
ST-6-24 功能描述:XFRMR PWR 115V 12VAC 1.6A RoHS:是 類別:變壓器 >> 功率 系列:ST 標準包裝:1 系列:260 類型:標準 最大功率:65 VA 主線圈:雙 副線圈:三路，中心抽頭 在某電流時的串聯輸出電壓:500 VAC @ 85mA，5 VAC @ 2A，6.3 VAC @ 2A 在某電流時的并聯輸出電壓:- 安裝類型:底座安裝 尺寸/尺寸:102.36mm L x 67.31mm W 高度 - 座高（最大）:66.80mm 端接類型:導線引線
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*